Nissan Rogue. Instruction — part 38
AV-144
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITHOUT BOSE]
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000011276833
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011276834
Regarding Wiring Diagram information, refer to
.
1.
CHECK REAR VIEW CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and rear view camera connectors.
3. Check continuity between around view monitor control unit connector M114 and rear view camera con-
nector D514.
4. Check continuity between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK REAR VIEW CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and rear view camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-208, "Removal and Installation"
3.
CHECK REAR VIEW CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and rear view camera connectors.
3. Check continuity between around view monitor control unit connector M114 and rear view camera con-
nector D514.
CONSULT Display
DTC Detection Condition
Possible Cause
Rear display output signal diag-
nosis (Harness disconnection)
[U111A]
Rear view camera image signal circuit open or
short.
Check rear view camera image signal circuit.
Around view monitor control unit
Rear view camera
Continuity
Connector
Terminals
Connector
Terminals
M114
50
D514
8
Yes
52
7
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M114
50
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M114
50
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
AV
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
AV-145
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITHOUT BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
4. Check continuity between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK REAR VIEW CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit and rear view camera connectors.
2. Turn ignition switch ON.
3. Check signal between the terminals of around view monitor control unit connector M114.
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-208, "Removal and Installation"
NO
>> Replace rear view camera. Refer to
AV-211, "Removal and Installation"
.
Around view monitor control unit
Rear view camera
Continuity
Connector
Terminals
Connector
Terminals
M114
53
D514
5
Yes
54
1
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M114
53
No
Around view monitor control unit connector M114
Condition
Reference value
(+)
(
−)
Terminal
Terminal
53
54
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
AV-146
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITHOUT BOSE]
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000011276835
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011276836
Regarding Wiring Diagram information, refer to
.
1.
CHECK RH SIDE CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and RH side camera connectors.
3. Check continuity between around view monitor control unit connector M114 and RH side camera connec-
tor D107.
4. Check continuity between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK RH SIDE CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and RH side camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-208, "Removal and Installation"
3.
CHECK RH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and RH side camera connectors.
CONSULT Display
DTC Detection Condition
Possible Cause
Right side display output signal
diagnosis (Harness disconnec-
tion)
[U111B]
Right side camera image signal circuit open or
short.
Check right side camera image signal circuit.
Around view monitor control unit
RH side camera
Continuity
Connector
Terminals
Connector
Terminals
M114
62
D107
7
Yes
64
8
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M114
62
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M114
62
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
AV
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
AV-147
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITHOUT BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
3. Check continuity between around view monitor control unit connector M114 and RH side camera connec-
tor D107.
4. Check continuity between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK RH SIDE CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit and RH side camera connectors.
2. Turn ignition switch ON.
3. Check signal between the terminals of around view monitor control unit connector M114.
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-208, "Removal and Installation"
NO
>> Replace RH side camera. Refer to
AV-210, "Removal and Installation"
Around view monitor control unit
RH side camera
Continuity
Connector
Terminals
Connector
Terminals
M114
65
D107
16
Yes
66
15
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M114
65
No
Around view monitor control unit connector M114
Condition
Reference value
(+)
(
−)
Terminal
Terminal
65
66
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст