Nissan Rogue. Instruction — part 251
DAS
WARNING SYSTEMS BUZZER
DAS-175
< REMOVAL AND INSTALLATION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
WARNING SYSTEMS BUZZER
Exploded View
INFOID:0000000011277341
Removal and Installation
INFOID:0000000011277342
REMOVAL
1. Remove instrument lower panel LH. Refer to
2. Remove warning systems buzzer from bracket on the back of the instrument lower panel LH.
INSTALLATION
Installation is in the reverse order of removal.
1.
Instrument lower panel LH
2.
Warning systems buzzer
A. Harness connector
Pawl
AWOIA0075ZZ
DAS-176
< REMOVAL AND INSTALLATION >
[DRIVER ASSISTANCE SYSTEM]
REAR VIEW CAMERA
REAR VIEW CAMERA
Removal and Installation
INFOID:0000000011277343
REMOVAL
1. Remove the back door outer finisher. Refer to
EXT-51, "Removal and Installation"
.
2. Disconnect washer tubes (1,3) and air tube (2) (if equipped).
3. Release pawl (B), disconnect harness connector (A) from rear
view camera and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Perform rear view camera calibration. Refer to
.
AWNIA3329ZZ
DAS
REAR VIEW CAMERA WASHER MOTOR
DAS-177
< REMOVAL AND INSTALLATION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
REAR VIEW CAMERA WASHER MOTOR
Exploded View
INFOID:0000000011277344
Removal and Installation
INFOID:0000000011277345
REMOVAL
1. Drain washer fluid.
2. Remove front over fender (RH). Refer to
EXT-30, "FRONT OVER FENDER : Removal and Installation"
.
3. Remove wind deflector (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
4. Remove engine side cover (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
5. Partially remove front fender protector (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
6. Disconnect the harness connector from the rear view camera washer motor.
7. Disconnect the washer tube from the rear view camera washer motor.
8. Remove the rear view camera washer motor.
9. Remove the washer tank seal (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Add water up to the top of washer tank inlet after installing. Check that no leaks exist.
• Fill washer tank with specified amount of fluid. Refer to
.
1.
Front and rear wiper motor
2.
Seal
3.
Rear view camera
washer motor
4.
Washer tank
Front
AWOIA0072ZZ
DAS-178
< REMOVAL AND INSTALLATION >
[DRIVER ASSISTANCE SYSTEM]
REAR VIEW CAMERA AIR PUMP MOTOR
REAR VIEW CAMERA AIR PUMP MOTOR
Exploded View
INFOID:0000000011277346
Removal and Installation
INFOID:0000000011277347
REMOVAL
1. Remove the rear bumper fascia under cover (LH). Refer to
2. Disconnect the air tubes from the rear view camera air pump motor.
3. Disconnect the harness connector from the rear view camera air pump motor.
4. Remove bolts and rear view camera air pump motor.
5. Remove nuts and remove bracket (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
1.
Rear floor
2.
Rear view camera air pump motor
3.
Bracket
Front
ALOIA0239ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст