Nissan Rogue. Instruction — part 332
DLK-170
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
3. Check voltage between rear door lock actuator RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock actuator RH. Refer to
DLK-267, "DOOR LOCK : Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM, all door lock actuator connectors.
2. Check continuity between BCM harness connector and rear door lock actuator RH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock actuator RH. Refer to
DLK-267, "DOOR LOCK : Removal and Installation"
.
NO
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
(+)
(–)
Condition
Voltage
(Approx.)
Rear door lock actuator RH
Connector
Terminal
D306
5
Ground
Door lock and unlock switch
Unlock
Battery voltage
6
Lock
BCM
Rear door lock actuator RH
Continuity
Connector
Terminal
Connector
Terminal
B23
148
D306
6
Yes
149
5
BCM
Ground
Continuity
Connector
Terminal
B23
148
No
149
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
B23
148
Ground
Door lock and unlock switch
Unlock
Battery voltage
149
Lock
2015 Rogue NAM
UNLOCK SENSOR
DLK-171
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
UNLOCK SENSOR
Component Function Check
INFOID:0000000011278887
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “UNLK SEN-DR” in “Data Monitor”.
3. Check that the function operates normally according to the following conditions:
Is the inspection result normal?
YES
>> Unlock sensor is OK.
NO
>> Refer to
DLK-171, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000011278888
Regarding Wiring Diagram information, refer to
.
1.
CHECK UNLOCK SENSOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly LH connector.
3. Check signal between front door lock assembly LH harness connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK UNLOCK SENSOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and front door lock assembly LH harness connector.
3. Check continuity between BCM harness connector and ground.
Monitor item
Condition
Status
UNLK SEN -DR
Driver side door
Lock
OFF
Unlock
ON
(+)
(–)
Signal
(Reference value)
Front door lock assembly LH
Connector
Terminal
D23
3
Ground
PKIB4960J
BCM
Front door lock assembly LH
Continuity
Connector
Terminal
Connector
Terminal
M19
104
D23
3
Yes
BCM
Ground
Continuity
Connector
Terminal
M19
104
No
2015 Rogue NAM
DLK-172
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
UNLOCK SENSOR
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK UNLOCK SENSOR
DLK-172, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly LH. Refer to
DLK-263, "DOOR LOCK : Removal and Installa-
.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> Inspection End.
Component Inspection
INFOID:0000000011278889
1.
CHECK UNLOCK SENSOR
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly LH connector.
3. Check continuity between front door lock assembly LH terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace front door lock assembly LH. Refer to
DLK-263, "DOOR LOCK : Removal and Installa-
.
Front door lock assembly LH
Ground
Continuity
Connector
Terminal
D23
4
Yes
Front door lock assembly LH
Condition
Continuity
Terminal
3
4
Driver side door
Unlock
Yes
Lock
No
2015 Rogue NAM
DOOR KEY CYLINDER SWITCH
DLK-173
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR KEY CYLINDER SWITCH
Component Function Check
INFOID:0000000011278890
1.
CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “KEY CYL LK-SW”, “KEY CYL UN-SW” in “Data Monitor”.
3. Check that the function operates normally according to the following conditions:
Is the inspection result normal?
YES
>> Door key cylinder switch is OK.
NO
>> Refer to
DLK-173, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000011278891
Regarding Wiring Diagram information, refer to
.
1.
CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly LH connector.
3. Check voltage between front door lock assembly LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR KEY CYLINDER SWITCH SIGNAL CIRCUIT
1. Disconnect the BCM connector.
2. Check continuity between BCM harness connector and front door lock assembly LH harness connector.
3. Check continuity between BCM harness connector and ground.
Monitor item
Condition
Status
KEY CYL LK-SW
Driver side door key cylinder
Lock
ON
Neutral / Unlock
OFF
KEY CYL UN-SW
Unlock
ON
Neutral / Lock
OFF
(+)
(–)
Voltage
(Approx.)
Front door lock assembly LH
Connector
Terminal
D23
5
Ground
5 V
6
BCM
Front door lock assembly LH
Continuity
Connector
Terminal
Connector
Terminal
M19
92
D23
6
Yes
93
5
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст