Nissan Rogue. Instruction — part 390
DLN-4
REAR FINAL DRIVE ASSEMBLY . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
UNIT DISASSEMBLY AND ASSEMBLY ...
ELECTRIC CONTROLLED COUPLING . . .
Exploded View . . . . . . . . . . . . . ...
Disassembly and Assembly . . . . . . . . ...
DIFFERENTIAL ASSEMBLY . . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Disassembly and Assembly . . . . . . . . ...
Adjustment . . . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . ..
DRIVE PINION . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Disassembly and Assembly . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
General Specifications . . . . . . . . . . ..
Preload Torque . . . . . . . . . . . . . .
Drive Gear Runout . . . . . . . . . . . .
Backlash . . . . . . . . . . . . . . . ...
PRECAUTIONS
DLN-5
< PRECAUTION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011278285
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000011278286
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precaution for Battery Service
INFOID:0000000011278287
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Service Notice or Precautions for Transfer
INFOID:0000000011278288
• After overhaul refill the transfer with new transfer oil.
• Check the oil level or replace the oil only with the vehicle parked on level surface.
• During removal or installation, keep inside of transfer clear of dust or dirt.
• Replace all tires at the same time. Always use tires of the proper size and the same brand and pattern. Fit-
ting improper size and unusual wear tires applies excessive force to vehicle mechanism and can cause lon-
gitudinal vibration.
• Disassembly should be done in a clean work area.
PIIB3706J
DLN-6
< PRECAUTION >
[TRANSFER: TY21C]
PRECAUTIONS
• Before proceeding with disassembly, thoroughly clean the transfer. It is important to prevent the internal
parts from becoming contaminated by dirt or other foreign matter.
• Check for the correct installation status prior to removal or disassembly. If matching marks are required, be
certain they do not interfere with the function of the parts when applied.
• All parts should be carefully cleaned with a general purpose, non-flammable solvent before inspection or
reassembly.
• Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace them
with a new one if necessary.
• Gaskets, seals, O-rings and lock nuts should be replaced any time when the transfer is disassembled.
• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If tight-
ening sequence is specified, use it.
• Observe the specified torque when assembling.
• Clean and flush the parts sufficiently and blow-dry them.
• Be careful not to damage sliding surfaces and mating surfaces.
• Use lint-free cloth or towels for wiping parts clean. Common shop rags can leave fibers that could interfere
with the operation of the transfer.
PREPARATION
DLN-7
< PREPARATION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000011278289
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tool
INFOID:0000000011278290
Tool number
(TechMate No.)
Tool name
Description
ST33061000
(J-8107-2)
Drift
a: 38 mm (1.50 in) dia.
b: 28.5 mm (1.122 in) dia.
Removing gear ring bearing inner race (trans-
fer case side)
KV381054S0
(J-34286)
Puller
Removing ring gear shaft oil seal
ST3127S000
(J-25765-A)
Preload gauge
Measuring preload torque
ZZA0810D
ZZA0601D
ZZA0503D
Tool name
Description
Power Tool
Loosening nuts, screws and bolts
Drift
a: 52 mm (2.05 in) dia.
b: 44 mm (1.73 in) dia.
Removing gear ring bearing inner race (trans-
fer cover side)
PIIB1407E
ZZA1002D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст