Nissan Rogue. Instruction — part 648
INSPECTION AND ADJUSTMENT
EXL-221
< BASIC INSPECTION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000011280847
CAUTION:
• When the IPDM E/R is replaced or disconnected and reconnected, perform “SENSOR INITIALIZE”
with CONSULT.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000011280848
1.
SENSOR INITIALIZE
CONSULT WORK SUPPORT
Perform “SENSOR INITIALIZE”. Refer to
EXL-221, "SENSOR INITIALIZE : Special Repair Requirement"
>> Work End.
SENSOR INITIALIZE
SENSOR INITIALIZE : Description
INFOID:0000000011280849
HEADLAMP AIMING CONTROL SYSTEM
Perform the sensor initialize when installing, removing and replacing the rear height sensor or suspension
components.
SENSOR INITIALIZE : Special Repair Requirement
INFOID:0000000011280850
CAUTION:
When performing aiming adjustment after the levelizer initialization, be sure to start the engine after
turning ignition switch OFF.
1.
VEHICLE CONDITION CHECK
1. Park the vehicle in the straight-forward position.
2. Unload the vehicle (no passenger aboard).
>> GO TO 2.
2.
SENSOR INITIALIZE
CONSULT WORK SUPPORT
1. Select “SENSOR INITIALIZE” in “Work Support” of “IPDM E/R”.
2. Select “START”.
3. When “INITIALIZE COMPLETE”, select “END”.
CAUTION:
If “INITIALIZE NOT DONE” is indicated, auto levelizer control unit detects that the sensor lever sig-
nal was changing. The sensor initialization is cancelled. In this case, turn the ignition switch OFF,
do not allow the vehicle height to change. Perform the sensor initialization again.
Is the sensor initialize completed?
YES
>> GO TO 3.
NO
>> Perform the sensor initialize again.
3.
SELF DIAGNOSTIC RESULT CHECK
Perform the “Self Diagnostic Result” with CONSULT. Check that any DTC is not detected.
Is any DTC detected?
YES
>> GO TO 2.
NO
>> GO TO 4.
4.
PERFORM HEADLAMP AIMING ADJUSTMENT
EXL-222
< BASIC INSPECTION >
[LED HEADLAMP]
INSPECTION AND ADJUSTMENT
Perform headlamp aiming adjustment. Refer to
EXL-262, "Aiming Adjustment Procedure"
>> Work End.
LED HEADLAMP OPERATION INSPECTION
EXL-223
< BASIC INSPECTION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LED HEADLAMP OPERATION INSPECTION
Diagnosis Procedure
INFOID:0000000011280851
1.
CHECK START
1. In the cool LED status (wait for more than 10 minutes after turning headlamp OFF), turn ON and turn OFF
headlamp for the several times. Check that headlamp operates normally each time.
2. In the cool LED status, turn headlamp ON, wait until headlamp enters to the stable status (approximately
5 minutes after turning headlamp ON), and then check that headlamp operates normally without blinking
or flickering.
3. In the warm LED status (turn headlamp ON for more than 15 minutes and wait for 1 minute after turning
OFF), turn ON and turn OFF headlamp for the several times. Check that headlamp operates normally
each time.
4. Turn headlamp ON for approximately 30 minutes, and then check that headlamp operates normally with-
out difference in brightness between LH and RH, blinking or flickering.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Refer to
EXL-224
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
POWER SUPPLY AND GROUND CIRCUIT
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis
Procedure
INFOID:0000000011421500
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSE
Check that the following fuse is not blown.
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Disconnect BCM connector M20.
2. Check voltage between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM) : Diag-
nosis Procedure
INFOID:0000000011421501
Regarding Wiring Diagram information, refer to
1.
CHECK FUSE
Terminal No.
Signal name
Fuse No.
161
BCM power supply
7 (10A)
BCM
Ground
Voltage
(Approx.)
Connector
Terminal
M20
161
—
Battery voltage
BCM
Ground
Continuity
Connector
Terminal
M20
170
—
Yes
171
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст