Nissan Rogue. Instruction — part 1220
WCS
SYSTEM
WCS-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions are fulfilled:
SIGNAL PATH
Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-
essary from signals below.
SEAT BELT REMINDER WARNING CHIME
SEAT BELT REMINDER WARNING CHIME : Seat belt Warning
INFOID:0000000011276458
SYSTEM DIAGRAM
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled:
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions are fulfilled:
SIGNAL PATH
Parking brake
During the operation (parking brake switch ON).
Vehicle speed
Approximately 4.3 MPH (7 km/h) or more.
Operation conditions
Operation conditions
Ignition switch
OFF
Parking brake
Release condition (parking brake switch OFF).
Vehicle speed
Approximately 1.9 MPH (3 km/h) or less.
Signal name
Signal source
Ignition switch signal
—
Parking brake switch signal
Parking brake switch
Combination meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
AWNIA2652GB
Operation conditions
Ignition switch
ON
Driver seat belt
Unfastened [seat belt buckle switch LH ON]
Operation conditions
Ignition switch
OFF
Driver seat belt
Fastened (seat belt buckle switch LH OFF)
6 seconds after the start of warning sound.
WCS-10
< SYSTEM DESCRIPTION >
SYSTEM
1. BCM requires warning chime output to combination meter when it judges seat belt warning chime is nec-
essary from signals below.
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
KEY WARNING CHIME
KEY WARNING CHIME : Key Warning Chime
INFOID:0000000011276459
SYSTEM DIAGRAM
WARNING CHIME OPERATION CONDITIONS
If all of the following conditions are fulfilled:
WARNING CHIME CANCEL CONDITIONS
Warning is canceled if any of the following conditions are fulfilled:
SIGNAL PATH
1. BCM detects key inserted into the ignition switch, and sends key warning signal to combination meter with
CAN communication line.
Signal name
Signal source
Ignition switch signal
—
Seat belt buckle switch signal LH
Seat belt buckle switch LH
Combination meter
BCM
Signal name
Signal source
Buzzer output signal
BCM
Combination
meter
AWNIA3130GB
Operation conditions
Ignition switch
OFF
Key switch
ON (key is in key cylinder)
Driver side door
Open [front door switch LH ON]
Operation conditions
Ignition switch
ON
Key switch
ON (key is removed from key cylinder)
Driver side door
Close [front door switch LH OFF]
Signal name
Signal source
Ignition switch signal
—
WCS
SYSTEM
WCS-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
2. Combination meter sounds integrated buzzer, when it receives a buzzer output signal from BCM.
Key switch signal
Key switch
BCM
Driver door switch signal
Front door switch LH
BCM
Signal name
Signal source
Buzzer output signal
BCM
Combination
meter
Signal name
Signal source
WCS-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
DIAGNOSIS SYSTEM (COMBINATION METER)
Description
INFOID:0000000011403293
COMBINATION METER SELF-DIAGNOSIS MODE
The following meter functions can be checked during Combination Meter Self-Diagnosis Mode:
• Pointer sweep of speedometer, tachometer and gauges.
• Illumination of all LCD segments and color patterns for meter displays.
• Illumination of all lamps/LEDs that are controlled by the combination meter (regardless of switch status).
STARTING COMBINATION METER SELF-DIAGNOSIS MODE
NOTE:
• Check combination meter power supply and ground circuits if self-diagnosis mode does not start. Refer to
MWI-60, "COMBINATION METER : Diagnosis Procedure"
. Replace combination meter if power supply and
ground circuits are found to be normal and self-diagnosis mode does not start. Refer to
• Combination meter self-diagnosis mode will function with the ignition switch in ON. Combination meter self-
diagnosis mode will exit upon turning the ignition switch to OFF.
How to Initiate Self-Diagnosis Mode
1. Turn ignition switch OFF.
2. While pressing the trip reset switch (1), turn ignition switch ON.
3. Keep the trip reset switch for 1 seconds or more.
4. Press the trip reset switch at least 3 times. (Within 7 seconds
after the ignition switch is turned ON.)
5. “Work instruction code” is indicated in the top portion of informa-
tion display and self-diagnosis is started.
6. The mode switches in the order shown below each time the trip
reset switch is pressed.
NOTE:
If the trip reset switch is not operated for 20 seconds or more, the
self-diagnosis mode is automatically cancelled.
AWNIA3394ZZ
Test order
Test item
Description
1
Work instruction code
This item is displayed, but not used.
2
Part number
3
Software code
4
EEPROM code
5
Hardware code
6
P.C.B code
7
Circuit check
The pointer of the following items moves from 0 to MAX twice.
• Speedometer
• Tachometer
• Engine coolant temperature gauge
• Fuel gauge
NOTE:
If any one of the pointers does not sweep, replace combination meter.
8
Color check
*1
Performs the color check of the information display.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст