Nissan Rogue. Instruction — part 917
MWI
SYSTEM
MWI-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
INFORMATION DISPLAY : System Description
INFOID:0000000011279784
SYSTEM DIAGRAM
FUNCTION
The information display can indicate the following items:
• Outside air temperature
• Trip computer
• Intelligent Key operation information
• CVT shift position indicator
• Odometer
• Warning/Indication messages (door open, lift gate open, low oil pressure, CVT, AWD, I-Key, low fuel, low
washer fluid, release parking brake, low tire pressure and loose fuel cap).
OUTSIDE AIR TEMPERATURE INDICATION
The combination meter receives the ambient sensor signal and displays the ambient temperature in the infor-
mation display.
LOOSE FUEL CAP MESSAGE
The LOOSE FUEL CAP message will display in the information display when the fuel-filler cap is not tightened
correctly. The message will turn off as soon as the ECM detects the fuel-filler cap is properly tightened. The
ECM provides a loose fuel cap signal to the combination meter via CAN communication lines.
LOW TIRE PRESSURE WARNING
AWNIA3719GB
MWI-16
< SYSTEM DESCRIPTION >
SYSTEM
This warning appears when the BCM detects low inflation pressure or a system malfunction. The BCM sends
a signal to the combination meter via CAN communication to illuminate the low tire pressure warning lamp. In
addition, a warning message will be displayed in the vehicle information display.
DOOR OPEN WARNING
This warning appears when the ignition switch is ON and the door is open. The BCM receives a door switch
signal from the door open door switch. The BCM sends the door switch signal to the combination meter via
CAN communication lines.
LIFTGATE OPEN WARNING
This warning appears when the ignition switch is ON and the liftgate is opened. The BCM receives a back door
switch signal from the back door switch. The BCM sends the door switch signal to the combination meter via
CAN communication lines.
LOW FUEL WARNING
This warning appears when the fuel level in the fuel tank is low.
LOW WINDSHIELD WASHER FLUID WARNING
When the windshield washer fluid level is low, the washer fluid level switch provides a ground signal to the
combination meter and the warning is displayed. Once fluid is added, the switch opens and the warning is no
longer displayed.
RELEASE PARKING BRAKE WARNING
When the parking brake is applied, the parking brake switch provides a ground signal to the combination
meter. When the vehicle speed is greater than 4 MPH (7 km/h), the message is displayed and the warning
chime sounds.
SHIFT POSITION INDICATOR
The combination meter activates the shift position indicator and instruction mode information based on signals
received from TCM via CAN communication.
LOW OIL PRESSURE WARNING
The low oil pressure warning appears in the information display when the combination meter receives a low
engine oil pressure signal from the ECM via CAN communication.
WARNING CHECK INDICATION
The combination meter can cause an interrupt on the information display to indicate a warning, based on sig-
nals received from each unit and switch.
Refer to Owner’s Instruction for additional information display items.
COMPASS
COMPASS : Description
INFOID:0000000011279785
DESCRIPTION
With the ignition switch in the ON position, and the mode or (N)
switch ON, the compass display will indicate the direction the vehicle
is heading.
Vehicle direction is displayed as follows:
• N: north
• E: east
• S: south
• W: west
ZONE VARIATION SETTING PROCEDURE
The difference between magnetic north and geographical north can sometimes be great enough to cause
false compass readings. This difference is known as variance. In order for the compass to operate properly
(accurately) in a particular zone, the zone variation must be calibrated using the following procedure.
LKIA0447E
MWI
SYSTEM
MWI-17
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Zone Variation Chart
1. Determine your location on the zone map.
2. Turn the ignition switch to the ON position.
3. Press and hold the (N) switch for about 5 seconds. The current zone number will appear in the display.
4. Press the mode or (N) switch repeatedly until the desired zone number appears in the display.
Once the desired zone number is displayed, stop pressing the mode or (N) switch and the display will show a
compass direction after a few seconds.
NOTE:
Use zone number 5 for Hawaii.
CALIBRATION PROCEDURE
The compass display is equipped with an automatic correction function. If the compass display reads “CAL” or
the direction is not shown correctly, perform the correction procedure below.
1. Press and hold the (N) switch for about 10 seconds. The display
will read “CAL”.
2. Drive the vehicle slowly in a circle, in an open, safe place. The
initial calibration is completed in about 3 turns.
NOTE:
In places where the terrestrial magnetism is extremely disturbed, the
initial correction may start automatically.
WKIA4148E
LKIA0447E
MWI-18
< SYSTEM DESCRIPTION >
OPERATION
OPERATION
Switch Name and Function
INFOID:0000000011279786
STEERING SWITCH
METER CONTROL SWITCH
AWNIA3392ZZ
No.
Switch name
Operation
Description
1.
Enter/Up/Down switch
Press
The information display settings can be changed.
2.
Display switch
3.
Back switch
AWNIA3393ZZ
No.
Switch name
Operation
Description
1.
Illumination control switch
Press
An illuminance level of the back light of the combination meter can be adjusted.
2.
Trip reset switch
Press
• The trip meter can be switched between A and B.
• Trip meter A/B can be reset by pressing and holding the trip reset switch.
• A trip computer value displayed on the information display can be reset by
pressing and holding the trip reset switch for 1 second or more.
• All trip computer values can be reset by pressing and holding the trip reset
switch for 3 seconds or more.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст