Nissan Rogue. Instruction — part 670
COWL TOP
EXT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
COWL TOP
Exploded View
INFOID:0000000011280033
Removal and Installation
INFOID:0000000011280034
COWL TOP COVER
Removal
1. Remove front wiper arms (LH/RH). Refer to
WW-62, "Removal and Installation"
2. Release pawls using suitable tool (A) and remove cowl top side
trim cover (1) (LH/RH).
: Pawl
1.
Cowl top side trim cover (RH)
2.
Cowl top cover screen
3.
Cowl top cover seal
4.
EPT seal
5.
Cowl top cover plug
6.
Cowl top cover
7.
Cowl top cover mask
8.
Cowl top extension seal
9.
Cowl top extension
10. Cowl top insulation
11. Cowl top side trim cover (LH)
AWKIA2902ZZ
ALKIA3399ZZ
EXT-26
< REMOVAL AND INSTALLATION >
COWL TOP
3. Disconnect front washer tube connector.
4. Remove cowl top cover clips, then pull forward to release cowl
top cover and remove.
CAUTION:
When performing the procedure after removing cowl top
cover, cover the lower end of windshield glass with ure-
thane etc.
5. Remove the following parts after removing cowl top cover (if necessary).
• Cowl top cover seal.
• Cowl top cover plug.
• Washer nozzle. Refer to
WW-59, "Removal and Installation - Front Washer Nozzle"
.
• Washer tube. Refer to
WW-59, "Removal and Installation - Front Washer Nozzle"
• EPT seal.
Installation
Installation is in the reverse order of removal.
CAUTION:
When installing cowl top cover, check that clips are securely fitted in body panel holes and then press
them in.
COWL TOP EXTENSION
Removal
1. Remove the front wiper drive assembly. Refer to
WW-68, "Removal and Installation"
2. Remove the cowl top extension bolts and the cowl top extension.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
JMKIA1316ZZ
JMKIA1317ZZ
COWL TOP
EXT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
When installing the cowl top extension, tighten the bolts to specifica-
tion in the order shown.
AWKIA2903ZZ
EXT-28
< REMOVAL AND INSTALLATION >
FENDER PROTECTOR
FENDER PROTECTOR
FENDER PROTECTOR
FENDER PROTECTOR : Exploded View
INFOID:0000000011280035
FENDER PROTECTOR : Removal and Installation
INFOID:0000000011280036
REMOVAL
1. Remove wheel and tire using power tool. Refer to
WT-67, "Removal and Installation"
2. Remove front over fender. Refer to
EXT-30, "FRONT OVER FENDER : Removal and Installation"
3. Remove front air spoiler.
4. Remove center mudguard screw. Refer to
EXT-35, "Exploded View - Center Mudguard"
5. Remove engine side cover.
6. Release front fender protector clips and remove front fender protector.
INSTALLATION
1.
Front fender protector
2.
Engine side cover
3.
Wind deflector
4.
Front fender
5.
Front over fender
Clip
Front
AWKIA3204ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст