Nissan Rogue. Instruction — part 25
AV-92
< SYSTEM DESCRIPTION >
[NAVIGATION WITHOUT BOSE]
SYSTEM
Front-side view area and guiding line
Birds-Eye View
• The birds-eye view image improves the visibility of obstacles all around the vehicle and assists backing and
parking.
• The images from the four cameras are converted into an overhead view, and the surroundings of the vehicle
are displayed.
• The blind spot area is displayed on the image to specify the boundary of the four cameras.
Birds-Eye view display image
JSNIA0771GB
AWNIA3345GB
AV
SYSTEM
AV-93
< SYSTEM DESCRIPTION >
[NAVIGATION WITHOUT BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Birds-Eye view display area
AWNIA3142GB
AV-94
< SYSTEM DESCRIPTION >
[NAVIGATION WITHOUT BOSE]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Description
INFOID:0000000011276796
The AV control unit on board diagnosis performs the functions listed in the table below:
Perform CONSULT diagnosis if the AV control unit on board diagnosis does not start or the screen does not
display anything.
On Board Diagnosis Function
INFOID:0000000011276797
METHOD OF STARTING
1. Turn the ignition ON.
Mode
Item
Content
Version
—
Version data of the AV control unit is dis-
played.
User Configuration
Touch Display Calibration
—
Allows correction of the position detec-
tion accuracy of the touch panel.
Radio
FM monitor
—
Monitors the dynamic values of the cur-
rent tuner
AM monitor
—
SXM monitor
—
Version data is displayed.
System State
Running System Status
• SD card slot Access
• Power Supply
• Speed Signal
• Direction Signal
• Illumination Signal
• GPS Antenna
• GPS Tracking
• Satellites Visible
• Satellites Tracked
• Microphone Current
• Steering wheel key
• Radio Antenna
• SXM Antenna
• USB Device
• iPod
®
firmware version
• BT Status
The current system status is displayed.
Speaker Test 4kHz
—
This activates a sequence of test tone
outputs to the audio circuits one after the
other for 1 second.
Speaker Test 100Hz
Display-Test
—
This provides a test sequence where
test displays (plain colored display: e.g.
white, black, red, blue, green) are shown
one after the other.
The respective color is shown for an in-
dicated period of time (parameter). After
the display test, the design of the display
previously available is stored. While the
screen shows a plain colored display, a
pixel malfunction may be detected.
Self Test
• SD Card Access
• BT Module Access
• Radio Antenna
• GPS Antenna
• SXM Antenna
A system self test is executed and the
results are stored into the error memory.
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-95
< SYSTEM DESCRIPTION >
[NAVIGATION WITHOUT BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
2. While pressing the APPS button, turn the TUNE-SCROLL dial
counterclockwise 3 or more clicks, then clockwise 3 or more
clicks, then counterclockwise 3 or more clicks. Shifting from cur-
rent screen to previous screen is performed by pressing BACK
button.
3. The trouble diagnosis initial screen is displayed, and Version,
User Config, Radio, System State or Self Test can be selected.
CONSULT Function
INFOID:0000000011276798
CONSULT FUNCTIONS
CONSULT performs the following functions via communication with the AV control unit:
ECU IDENTIFICATION
The part number of AV control unit is displayed.
SELF DIAGNOSTIC RESULT
DATA MONITOR
CONFIGURATION
AV-131, "CONFIGURATION (AV CONTROL UNIT) : Description"
CAN DIAG SUPPORT MNTR
LAN-14, "CAN Diagnostic Support Monitor"
.
ALNIA1591ZZ
ALNIA1378ZZ
Direct Diagnostic Mode
Description
Ecu Identification
The AV control unit part number is displayed.
Self Diagnostic Result
The AV control unit self diagnostic results are displayed.
Data Monitor
The AV control unit input/output data is displayed in real time.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing AV control unit.
CAN Diag Support Mntr
• The result of transmit/receive diagnosis of AV communication is displayed.
• The result of transmit/receive diagnosis of CAN communication is displayed.
Monitor Item [Unit]
Description
VHCL SPD SIG [On/Off]
Indicates vehicle speed signal received from combination meter on CAN communication
line.
ILLUM SIG [On/Off]
Indicates condition of illumination signal for the AV control unit.
IGN SIG [On/Off]
Indicates condition of ignition signal.
REV SIG [On/Off]
Indicates condition of reverse signal received from BCM.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст