Nissan Rogue. Instruction — part 80
AV-312
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
U1232 STEERING ANGLE SENSOR
U1232 STEERING ANGLE SENSOR
DTC Logic
INFOID:0000000011276974
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011276975
1.
ADJUST PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT OF STEERING ANGLE SEN-
SOR
When U1232 is detected, the predictive course line center position of steering angle sensor needs to be
adjusted.
>> Adjust the predictive course line center position of steering angle sensor. Refer to
DICTED COURSE LINE CENTER POSITION ADJUSTMENT : Work Procedure"
CONSULT Display
DTC Detection Condition
Possible Cause
ST ANG SEN CALIB
[U1232]
Predictive course line center position adjustment
of steering angle sensor is incomplete.
Adjust predictive course line center position ad-
justment of steering angle sensor.
AV
U1244 GPS ANTENNA
AV-313
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U1244 GPS ANTENNA
DTC Logic
INFOID:0000000011276976
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011276977
Regarding Wiring Diagram information, refer to
.
1.
GPS ANTENNA INSPECTION
Visually inspect the GPS antenna and antenna feeder. Refer to
AV-384, "Removal and Installation"
.
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning components.
2.
CHECK AV CONTROL UNIT VOLTAGE
1. Disconnect AV control unit connector M141.
2. Turn ignition switch ON.
3. Check voltage between AV control unit connector M141 and ground.
Is inspection result normal?
YES
>> Replace GPS antenna. Refer to
AV-384, "Removal and Installation"
.
NO
>> Replace AV control unit. Refer to
AV-369, "Removal and Installation"
.
CONSULT Display
DTC Detection Condition
Possible Cause
GPS ANTENNA CONN
[U1244]
Open or short to ground is detected in GPS an-
tenna connection.
• GPS antenna disconnection.
• Open or short to ground in GPS antenna signal
circuit.
AV control unit
Ground
Voltage
Connector
Terminal
M141
58
—
5.0 V
AV-314
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
U1258 SATELLITE RADIO ANTENNA
U1258 SATELLITE RADIO ANTENNA
DTC Logic
INFOID:0000000011276978
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011276979
Regarding Wiring Diagram information, refer to
.
1.
SATELLITE ANTENNA INSPECTION
Visually inspect the satellite antenna and antenna feeder. Refer to
.
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning components.
2.
CHECK AV CONTROL UNIT VOLTAGE
1. Turn ignition switch ON.
2. Check voltage between AV control unit connector M142 and ground.
Is inspection result normal?
YES
>> Replace satellite radio antenna
AV-385, "Removal and Installation"
.
NO
>> Replace AV control unit. Refer to
AV-369, "Removal and Installation"
.
CONSULT Display
DTC Detection Condition
Possible Cause
SXM ANTENNA CONN
[U1258]
Open or short to ground is detected in satellite
antenna connection.
• Satellite antenna disconnection.
• Open or short to ground in satellite antenna
signal circuit.
AV control unit
Ground
Voltage
Connector
Terminal
M142
56
—
5.0 V
AV
U1263 USB
AV-315
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U1263 USB
DTC Logic
INFOID:0000000011276980
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
1. If there is a device connected to the USB interface, disconnect it.
2. Turn ignition switch ON and wait for 2 seconds or more.
3. Perform “Self Diagnostic Result” for “MULTI AV”.
Is DTC U1263 displayed?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011276981
1.
CHECK USB INTERFACE HARNESS
Visually inspect USB interface harness. Refer to
AV-378, "Removal and Installation"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace USB interface harness. Refer to
AV-378, "Removal and Installation"
.
2.
CHECK USB INTERFACE HARNESS
Check USB interface harness. Refer to
Is the inspection result normal?
YES
>> Replace AV control unit. Refer to
AV-369, "Removal and Installation"
.
NO
>> Replace USB interface harness. Refer to
AV-378, "Removal and Installation"
.
CONSULT Display
DTC Detection Condition
Possible Cause
USB OVERCURRENT
[U1263]
Overcurrent in USB harness is detected.
• Device connected to USB interface.
• Harness between the AV control unit and USB
interface.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст