Nissan Rogue. Instruction — part 559
EM-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
EM
A
EM
N
O
P
CONTENTS
ENGINE MECHANICAL
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Draining Coolant and Engine Oil . ...
Precaution for Procedure without Cowl Top Cover
. ..
Parts Requiring Angle Tightening . . . . . . .....
Precautions For Engine Service . . . . . . . ....
Special Cautions to Ensure the Safe Disposal of
Sodium-filled Exhaust Valves . . . . . . . . ....
Precaution for Liquid Gasket . . . . . . . . .....
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION, AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting - Engine Noise . . . . . ...
Use the Chart Below to Help You Find the Cause
of the Symptom . . . . . . . . . . . . . .....
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . ..
Special Service Tools . . . . . . . . . . .
Commercial Service Tool . . . . . . . . . .
PERIODIC MAINTENANCE . . . . . . .
DRIVE BELTS . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Checking . . . . . . . . . . . . . . . . .
Tension Adjustment . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Removal and Installation of Drive Belt Auto-ten-
sioner . . . . . . . . . . . . . . . . . ..
AIR CLEANER FILTER . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SPARK PLUG . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
CAMSHAFT VALVE CLEARANCE . . . . ..
Camshaft valve clearance . . . . . . . . . ...
COMPRESSION PRESSURE . . . . . . ...
Compression pressure . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
AIR CLEANER AND AIR DUCT . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
INTAKE MANIFOLD . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
EXHAUST MANIFOLD AND THREE WAY
CATALYST . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
OIL PAN AND OIL STRAINER . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
IGNITION COIL . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
ROCKER COVER . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FUEL INJECTOR AND FUEL TUBE . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
EM-2
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
CYLINDER HEAD . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
Disassembly and Assembly . . . . . . . . ....
Inspection After Disassembly . . . . . . . . .
CAMSHAFT . . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
Inspection After Installation . . . . . . . . ....
VALVE TIMING CONTROL . . . . . . . ...
Exploded View . . . . . . . . . . . . . ....
Valve Timing Control Cover . . . . . . . . ....
OIL SEAL . . . . . . . . . . . . . . ...
VALVE OIL SEAL . . . . . . . . . . . . . .
VALVE OIL SEAL : Removal and Installation . . .
FRONT OIL SEAL . . . . . . . . . . . . . .
FRONT OIL SEAL : Removal and Installation . ....
REAR OIL SEAL . . . . . . . . . . . . . ...
REAR OIL SEAL : Removal and Installation . . ..
UNIT REMOVAL AND INSTALLATION . .
ENGINE ASSEMBLY . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation (FWD) . . . . . . . .
Removal and Installation (AWD) . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY ...
ENGINE STAND SETTING . . . . . . . ...
Setting . . . . . . . . . . . . . . . . . .
CYLINDER BLOCK . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . .
Inspection . . . . . . . . . . . . . . . ..
HOW TO SELECT PISTON AND BEARING ...
How to Select Piston and Bearing . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
General Specification . . . . . . . . . . ...
Drive belt . . . . . . . . . . . . . . . ...
Spark Plug . . . . . . . . . . . . . . .
Exhaust Manifold . . . . . . . . . . . . ..
Camshaft . . . . . . . . . . . . . . . ...
Cylinder Head . . . . . . . . . . . . . ..
Cylinder Block . . . . . . . . . . . . . ..
Main Bearing . . . . . . . . . . . . . .
PRECAUTIONS
EM-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011279924
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Draining Coolant and Engine Oil
INFOID:0000000011340778
Drain engine coolant and engine oil after the engine has cooled completely.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000011279925
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Parts Requiring Angle Tightening
INFOID:0000000011279926
• Use the Tool for the final tightening of the following engine parts:
- Camshaft sprocket (INT) bolt
- Cylinder head bolts
- Main bearing cap bolts
- Connecting rod cap bolts
- Crankshaft pulley bolt (The angle wrench is not required as bolt flange is provided with notches for angle
tightening)
PIIB3706J
Tool number
: KV10112100 (BT-8653-A)
EM-4
< PRECAUTION >
PRECAUTIONS
• Do not use a torque value for final tightening.
• Ensure thread and seat surfaces are clean and coated with engine oil.
Precautions For Engine Service
INFOID:0000000011279927
DISCONNECTING FUEL PIPING
• Before starting work, check no fire or spark producing items are in the work area.
• Release fuel pressure before disconnecting and disassembly.
• After disconnecting pipes, plug openings to stop fuel leaks.
DRAINING ENGINE COOLANT
Drain engine coolant and engine oil when the engine is cooled.
INSPECTION, REPAIR AND REPLACEMENT
Before repairing or replacing, thoroughly inspect parts. Inspect new replacement parts in the same way, and
replace if necessary.
REMOVAL AND DISASSEMBLY
• When instructed to use SST, use specified tools. Always be careful to work safely, avoid forceful or unin-
structed operations.
• Exercise maximum care to avoid damage to mating or sliding surfaces.
• Dowel pins are used for several parts alignment. When replacing and reassembling parts with dowel pins,
check that dowel pins are installed in the original position.
• Cover openings of engine system with a tape or equivalent, if necessary, to seal out foreign materials.
• Mark and arrange disassembly parts in an organized way for easy troubleshooting and reassembly.
• When loosening nuts and bolts, as a basic rule, start with the one furthest outside, then the one diagonally
opposite, and so on. If the order of loosening is specified, do exactly as specified. Power tools may be used
in the step.
ASSEMBLY AND INSTALLATION
• Use torque wrench to tighten bolts or nuts to specification.
• When tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with the
ones in center, then ones on inside and outside diagonally in this order. If the order of tightening is specified,
do exactly as specified.
• Replace with new gasket, packing, oil seal or O-ring.
• Thoroughly wash, clean, and air-blow each part. Carefully check engine oil or engine coolant passages for
any restriction and blockage.
• Avoid damaging sliding or mating surfaces. Completely remove foreign materials such as cloth lint or dust.
Before assembly, oil sliding surfaces well.
• Release air within route when refilling after draining engine coolant.
• After repairing, start the engine and increase engine speed to check engine coolant, fuel, engine oil, and
exhaust gases for leaks.
Special Cautions to Ensure the Safe Disposal of Sodium-filled Exhaust Valves
INFOID:0000000011279928
Handling and disposal of sodium-filled exhaust valves requires spe-
cial care and consideration. Under conditions such as breakage with
subsequent contact with water, metal sodium which lines the inner
portion of exhaust valve will react violently, forming sodium hydrox-
ide and hydrogen which may result in an explosion. Sodium-filled
exhaust valve is identified on the top of its stem as shown in illustra-
tion.
DEALER DISPOSAL INSTRUCTIONS
(A)
: Identification mark of sodium-filled exhaust valve
AWBIA1366ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст