Nissan Rogue. Instruction — part 384
DLK-378
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000011279159
Check the clearance and the surface height between back door and each part by visual inspection and tactile
feel. If the clearance and the surface height are out of specification, adjust them according to the adjustment
procedure.
1.
Back door assembly
2.
Roof panel
3.
Rear spoiler
4.
Back door glass
5.
Rear combination lamp
6.
Back-up lamp
7.
Rear fender
8.
Side spoiler
AWKIA2918ZZ
2015 Rogue NAM
BACK DOOR
DLK-379
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit: mm (in)
1. Loosen back door hinge nuts (door side).
2. Lift up back door approximately 100 – 150 mm (3.94 – 5.91 in) height then close it lightly and check that it
is engaged firmly with back door closed.
3. Check the clearance and surface height according to the specifications provided.
4. Tighten back door hinge nuts to specified torque.
CAUTION:
• After installation, check back door open/close, lock/unlock operation.
• Check back door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-
purpose grease.
• After adjusting, apply touch-up paint (body color) to the head of rear door hinge bolts and nuts.
• Perform calibration of automatic back door position information. Refer to
.
BACK DOOR STRIKER
BACK DOOR STRIKER : Removal and Installation
INFOID:0000000011279160
REMOVAL
1. Release back door striker cover (1) pawls using a suitable tool
and remove.
: Pawl
2. Remove the back door welt. Refer to
DLK-380, "BACK DOOR WEATHER-STRIP : Removal and Installa-
3. Remove bolts and back door striker.
CAUTION:
• Do not reuse back door striker bolts.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse back door striker bolts.
• Tighten bolts to specification. Refer to
• After installation, check back door open/close operation. If necessary, adjust the door striker. Refer
DLK-380, "BACK DOOR STRIKER : Adjustment"
Portion
Section
Item
Measurement
Standard
Paraelleism
Roof panel – Rear spoiler
A – A
E
Clearance
7.0
± 2.0 (0.28 ± 0.08)
2.0 (0.08)
F
Surface height
1.7
± 2.0 (0.07 ± 0.08)
2.0 (0.08)
Side spoiler – Back door glass
B – B
G
Clearance
5.5
± 2.0 (0.22 ± 0.08)
2.0 (0.08)
H
Surface height
—
—
Rear combination lamp – Back-up lamp
C – C
J
Clearance
4.5
± 2.0 (0.18 ± 0.08)
2.0 (0.08)
K
Surface height
2.2
± 2.0 (0.09 ± 0.08)
2.0 (0.08)
Rear fender – Back door
D – D
M
Clearance
4.7
± 2.0 (0.19 ± 0.08)
2.0 (0.08)
N
Surface height
2.5
± 2.0 (0.10 ± 0.08)
2.0 (0.08)
ALKIA3411ZZ
2015 Rogue NAM
DLK-380
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR STRIKER : Adjustment
INFOID:0000000011279161
DOOR STRIKER ADJUSTMENT
1. Loosen door striker bolts
2. Adjust door striker so that it becomes parallel with front door lock
insertion direction.
3. Tighten door striker bolts to specification. Refer to
BACK DOOR HINGE
BACK DOOR HINGE : Removal and Installation
INFOID:0000000011279162
REMOVAL
1. Remove back door assembly. Refer to
DLK-376, "BACK DOOR ASSEMBLY : Removal and Installation"
2. Partially remove the rear of the headlining. Refer to
INT-30, "Removal and Installation"
.
3. Remove nuts and back door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten nuts to specification. Refer to
.
• Apply anticorrosive agent onto the surface between hinge and body side.
• After installation, perform the back door assembly adjustment procedure. Refer to
BACK DOOR WEATHER-STRIP
BACK DOOR WEATHER-STRIP : Removal and Installation
INFOID:0000000011279163
REMOVAL
Carefully remove back door weather-strip from opening door joint.
INSTALLATION
1. Beginning with upper section, align weather-strip mark with vehicle center position mark and install
weather strip to the vehicle.
2. For the lower section, align weather-strip seam with center of back door striker.
NOTE:
Pull weather-strip gently to ensure that there are no loose sections.
ALKIA3218ZZ
2015 Rogue NAM
HOOD LOCK
DLK-381
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD LOCK
Exploded View
INFOID:0000000011279164
HOOD LOCK
HOOD LOCK : Removal and Installation
INFOID:0000000011279165
REMOVAL
1. Disconnect hood lock release cable and secondary latch cable from hood lock.
2. Remove bolts and hood lock.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten bolts to specified torque. Refer to
• Check that hood lock release cable and secondary latch cable are properly engaged with hood lock.
• After installation, perform hood assembly adjustment procedure. Refer to
• After adjusting, perform hood lock inspection. Refer to
DLK-381, "HOOD LOCK : Inspection"
HOOD LOCK : Inspection
INFOID:0000000011279166
NOTE:
If the hood lock cable is bent or deformed, replace it.
1. Check that secondary latch is properly engaged with secondary striker with hoods own weight.
2. While operating hood lock release handle, carefully check that the front end of hood assembly is raised by
approximately 20.0 mm (0.79 in). Also check that hood lock release handle returns to the original position.
3. Check that hood lock release handle operates at 49 N (5.0 kg-m, 11.0 ft-lb) or below.
1.
Hood lock release handle
2.
Hood lock release cable
3.
Hood lock
4.
Secondary latch
A.
Clip
AWKIA2919ZZ
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст