Nissan Rogue. Instruction — part 205
CO-16
< REMOVAL AND INSTALLATION >
RADIATOR
• To install hose clamps (1), check that the dimension (A) from the
end of the hose clamp on the radiator hose (2) to the hose clamp is
within the reference value.
Inspection
INFOID:0000000011279707
INSPECTION AFTER INSTALLATION
• Start and warm up the engine. Check visually and verify that there are no engine coolant leaks, if engine
coolant leaks are found perform inspection. Refer to
Dimension “A”
: (-3) – (+3) mm [(-0.12)
− (+0.12) in]
JSBIA0241ZZ
COOLING FAN
CO-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
COOLING FAN
Exploded View
INFOID:0000000011279708
Removal and Installation
INFOID:0000000011279709
REMOVAL
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
engine coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter
turn to allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Disconnect battery negative terminal.
2. Disconnect battery positive terminal. Refer to
3. Depower SRS system. Refer to
.
4. Drain engine coolant from radiator. Refer to
.
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine coolant on the drive belt.
5. Remove engine under cover. Refer to
EXT-37, "ENGINE UNDER COVER : Removal and Installation"
6. Remove front air spoiler. Refer to
.
7. Remove fender protector side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
8. Remove air duct (inlet). Refer to
9. Remove radiator core support (upper). Refer to
DLK-244, "Removal and Installation"
(WITH INTELLI-
GENT KEY SYSTEM),
DLK-365, "Removal and Installation"
(WITHOUT INTELLIGENT KEY SYSTEM).
1.
Fan shroud
2.
Fan motor (LH)
3.
Fan motor (RH)
4.
Cooling fan (RH)
5.
Cooling fan (LH)
Front
AWBIA1962ZZ
CO-18
< REMOVAL AND INSTALLATION >
COOLING FAN
10. Remove radiator hose (upper) from radiator. Refer to
CAUTION:
Do not spill engine coolant on the drive belt.
11. Disconnect harness connector from cooling fan controller.
12. Remove harness retainers from fan shroud.
13. Remove CVT cooler hose retainers from fan shroud.
14. Remove reservoir tank hose from fan shroud. Refer to
.
15. Remove fan shroud. Refer to
CAUTION:
Be careful not to damage the radiator.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not spill engine coolant in the engine compartment. Use a shop cloth to absorb engine coolant.
NOTE:
Cooling fan is controlled by ECM. For details, refer to
EC-66, "On Board Diagnosis Function"
.
Disassembly and Assembly
INFOID:0000000011279710
DISASSEMBLY
1. Remove cooling fan mounting nuts, and then remove the cooling fans (RH and LH).
2. Remove fan motor cover and fan motors (RH and LH).
ASSEMBLY
Assembly is in the reverse order of disassembly.
CAUTION:
Apply high thread locking sealant to cooling fan motor shaft.
Inspection
INFOID:0000000011279711
INSPECTION AFTER DISASSEMBLY
Cooling Fan
Inspect cooling fan for cracks or unusual bends.
• If anything is found, replace cooling fan.
WATER PUMP
CO-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
WATER PUMP
Exploded View
INFOID:0000000011279712
Removal and Installation
INFOID:0000000011279713
REMOVAL
1. Drain engine coolant. Refer to
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pres-
sure coolant escaping from the radiator.
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine coolant on the drive belt.
2. Remove the generator. Rafer to
CHG-20, "Removal and Installation"
.
3. Remove water pump.
• Engine coolant will leak from the cylinder block.
CAUTION:
• Handle water pump vane so that it does not contact any other parts.
• Water pump cannot be disassembled and should be replaced as a unit.
INSTALLATION
1. Tighten water pump bolts in sequence to specification.
CAUTION:
1.
Cylinder block
2.
Water pump
3.
Water pump gasket
4.
Water pump housing
5.
O-ring
6.
Water pipe
7.
Water pump housing gasket
A.
Refer to INSTALLATION
Front
AWBIA1963ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст