Nissan Rogue. Instruction — part 60
AV-232
< SYSTEM DESCRIPTION >
[NAVIGATION WITH BOSE]
SYSTEM
Birds-Eye view display area
AWNIA3142GB
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-233
< SYSTEM DESCRIPTION >
[NAVIGATION WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Description
INFOID:0000000011276925
The AV control unit on board diagnosis performs the functions listed in the table below:
Perform CONSULT diagnosis if the AV control unit on board diagnosis does not start or the screen does not
display anything.
On Board Diagnosis Function
INFOID:0000000011276926
METHOD OF STARTING
1. Turn the ignition ON.
Mode
Item
Content
Version
—
Version data of the AV control unit is dis-
played.
User Configuration
Touch Display Calibration
—
Allows correction of the position detec-
tion accuracy of the touch panel.
Radio
FM monitor
—
Monitors the dynamic values of the cur-
rent tuner
AM monitor
—
SXM monitor
—
Version data is displayed.
System State
Running System Status
• SD card slot Access
• Power Supply
• Speed Signal
• Direction Signal
• Illumination Signal
• GPS Antenna
• GPS Tracking
• Satellites Visible
• Satellites Tracked
• Microphone Current
• Steering wheel key
• Radio Antenna
• SXM Antenna
• USB Device
• iPod
®
firmware version
• BT Status
The current system status is displayed.
Speaker Test 4kHz
—
This activates a sequence of test tone
outputs to the audio circuits one after the
other for 1 second.
Speaker Test 100Hz
Display-Test
—
This provides a test sequence where
test displays (plain colored display: e.g.
white, black, red, blue, green) are shown
one after the other.
The respective color is shown for an in-
dicated period of time (parameter). After
the display test, the design of the display
previously available is stored. While the
screen shows a plain colored display, a
pixel malfunction may be detected.
Self Test
• SD Card Access
• BT Module Access
• Radio Antenna
• GPS Antenna
• SXM Antenna
A system self test is executed and the
results are stored into the error memory.
AV-234
< SYSTEM DESCRIPTION >
[NAVIGATION WITH BOSE]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
2. While pressing the APPS button, turn the TUNE-SCROLL dial
counterclockwise 3 or more clicks, then clockwise 3 or more
clicks, then counterclockwise 3 or more clicks. Shifting from cur-
rent screen to previous screen is performed by pressing BACK
button.
3. The trouble diagnosis initial screen is displayed, and Version,
User Config, Radio, System State or Self Test can be selected.
CONSULT Function
INFOID:0000000011276927
CONSULT FUNCTIONS
CONSULT performs the following functions via communication with the AV control unit:
ECU IDENTIFICATION
The part number of AV control unit is displayed.
SELF DIAGNOSTIC RESULT
DATA MONITOR
CONFIGURATION
AV-280, "CONFIGURATION (AV CONTROL UNIT) : Description"
CAN DIAG SUPPORT MNTR
LAN-14, "CAN Diagnostic Support Monitor"
.
ALNIA1591ZZ
ALNIA1378ZZ
Direct Diagnostic Mode
Description
Ecu Identification
The AV control unit part number is displayed.
Self Diagnostic Result
The AV control unit self diagnostic results are displayed.
Data Monitor
The AV control unit input/output data is displayed in real time.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing AV control unit.
CAN Diag Support Mntr
• The result of transmit/receive diagnosis of AV communication is displayed.
• The result of transmit/receive diagnosis of CAN communication is displayed.
Monitor Item [Unit]
Description
VHCL SPD SIG [On/Off]
Indicates vehicle speed signal received from combination meter on CAN communication
line.
ILLUM SIG [On/Off]
Indicates condition of illumination signal for the AV control unit.
IGN SIG [On/Off]
Indicates condition of ignition signal.
REV SIG [On/Off]
Indicates condition of reverse signal received from BCM.
AV
DIAGNOSIS SYSTEM (AROUND VIEW MONITOR CONTROL UNIT)
AV-235
< SYSTEM DESCRIPTION >
[NAVIGATION WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DIAGNOSIS SYSTEM (AROUND VIEW MONITOR CONTROL UNIT)
WITHOUT DRIVER ASSISTANCE SYSTEM
WITHOUT DRIVER ASSISTANCE SYSTEM : CONSULT Function
INFOID:0000000011276928
CONSULT FUNCTIONS
CONSULT performs the following functions via communication with the around view monitor control unit:
ECU IDENTIFICATION
The part number of around view monitor control unit is displayed.
SELF DIAGNOSTIC RESULT
AV-248, "WITHOUT DRIVER ASSISTANCE SYSTEM : DTC Index"
.
DATA MONITOR
WORK SUPPORT
Direct Diagnostic Mode
Description
Ecu Identification
The around view monitor control unit part number is displayed.
Self Diagnostic Result
The around view monitor control unit self diagnostic results are displayed.
Data Monitor
The around view monitor control unit input/output data is displayed in real time.
Work support
The settings for around view monitor control unit functions can be changed.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing around view monitor control unit.
CAN Diag Support Mntr
The result of transmit/receive diagnosis of CAN communication is displayed.
Monitor Item
Description
ST ANGLE SENSOR SIGNAL [On/Off] Indicates condition of steering angle sensor signal.
REVERSE SIGNAL [On/Off]
Indicates selector lever position.
VEHICLE SPEED SIGNAL [mph/km/h] Indicates condition of vehicle speed signal.
CAMERA SWITCH SIGNAL [On/Off]
Indicates condition of camera switch signal.
CAMERA OFF SIGNAL [On/Off]
Indicates condition of camera OFF signal.
ST ANGLE SENSOR TYPE [Absolute] Indicates steering angle sensor type.
ST GEAR RATIO TYPE [Type O]
Indicates steering gear ratio type.
STEERING POSITION [LHD/RHD]
Indicates LH or RH drive type.
REAR CAMERA IMAGE SIGNAL [OK/
NG]
Indicates condition of camera image signal.
F-CAMERA IMAGE SIGNAL [OK/NG]
Indicates condition of camera image signal.
DR-SIDE CAMERA IMAGE SIG [OK/
NG]
Indicates condition of camera image signal.
PA-SIDE CAMERA IMAGE SIG [OK/
NG]
Indicates condition of camera image signal.
Support Item
Setting
Description
NON-VIEWABLE AREA REMINDER
ON
ON/OFF setting of non-viewable area can be performed.
OFF
PREDICTIVE COURSE LINE
DISPLAY
ON
ON/OFF setting of predictive course line display can be performed.
OFF
INITIALIZE CAMERA IMAGE
CALIBRATION
—
Factory image calibration restoration can be performed.
STEERING ANGLE SENSOR
ADJUSTMENT
—
Steering angle sensor neutral position adjustment can be performed.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст