Nissan Rogue. Instruction — part 237
DAS
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
DAS-119
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-380, "Removal and Installation"
NO
>> Replace front camera. Refer to
AV-381, "Removal and Installation"
.
Around view monitor control unit connector M114
Condition
Reference value
(+)
(
−)
Terminal
Terminal
71
72
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
DAS-120
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000011419759
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011459690
Regarding Wiring Diagram information, refer to
.
WITHOUT DRIVER ASSISTANCE SYSTEM
1.
CHECK LH SIDE CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and LH side camera connectors.
3. Check continuity between around view monitor control unit connector M103 and LH side camera connec-
tor D14.
4. Check continuity between around view monitor control unit connector M103 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK LH SIDE CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and LH side camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector M103 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-380, "Removal and Installation"
3.
CHECK LH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
CONSULT Display
DTC Detection Condition
Possible Cause
Left side display output signal
diagnosis (Harness disconnec-
tion)
[U111D]
Left side camera image signal circuit open or
short.
Check left side camera image signal circuit.
Around view monitor control unit
LH side camera
Continuity
Connector
Terminals
Connector
Terminals
M103
30
D14
7
Yes
29
8
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M103
30
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M103
30
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
DAS
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
DAS-121
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
2. Disconnect around view monitor control unit and LH side camera connectors.
3. Check continuity between around view monitor control unit connector M103 and LH side camera connec-
tor D14.
4. Check continuity between around view monitor control unit connector M103 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK LH SIDE CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit and LH side camera connectors.
2. Turn ignition switch ON.
3. Check signal between the terminals of around view monitor control unit connector M103.
Is the inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-380, "Removal and Installation"
NO
>> Replace LH side camera. Refer to
AV-382, "Removal and Installation"
.
WITH DRIVER ASSISTANCE SYSTEM
1.
CHECK LH SIDE CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and LH side camera connectors.
3. Check continuity between around view monitor control unit connector M114 and LH side camera connec-
tor D14.
4. Check continuity between around view monitor control unit connector M114 and ground.
Around view monitor control unit
LH side camera
Continuity
Connector
Terminals
Connector
Terminals
M103
32
D14
16
Yes
31
15
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M103
32
No
Around view monitor control unit connector M103
Condition
Reference value
(+)
(
−)
Terminal
Terminal
32
31
CAMERA switch is ON or se-
lector lever in R (reverse).
JSNIA0834GB
Around view monitor control unit
LH side camera
Continuity
Connector
Terminals
Connector
Terminals
M114
56
D14
7
Yes
58
8
DAS-122
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK LH SIDE CAMERA POWER SUPPLY VOLTAGE
1. Connect around view monitor control unit and LH side camera connectors.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-380, "Removal and Installation"
3.
CHECK LH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit and LH side camera connectors.
3. Check continuity between around view monitor control unit connector M114 and LH side camera connec-
tor D14.
4. Check continuity between around view monitor control unit connector M114 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
CHECK LH SIDE CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit and LH side camera connectors.
2. Turn ignition switch ON.
3. Check signal between the terminals of around view monitor control unit connector M114.
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M114
56
No
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M114
56
—
CAMERA switch is ON or
selector lever in R (re-
verse).
6.0 V
Around view monitor control unit
LH side camera
Continuity
Connector
Terminals
Connector
Terminals
M114
59
D14
16
Yes
60
15
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M114
59
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст