Nissan Rogue. Instruction — part 1042
SE-34
< REMOVAL AND INSTALLATION >
FRONT SEAT
MANUAL SEAT
16. Occupant classification system
sensor
17. Occupant classification sys-
tem control unit
18. Occupant classification system
bracket
19. Wiring harness bracket
20. Power seat switch
21. Seat cushion outer finisher (RH)
22. Seat slide knob
23. Seat recline knob
24. Seat cushion inner finisher (RH)
25. Seat cushion rear finisher (RH)
26. Side air bag module (not ser-
viceable)
27. Seat cushion frame
28. Seat belt buckle
29. Seat cushion rear finisher (LH) 30. Seatback frame
31. Seatback bracket
32. Headrest holder (locked)
33. Headrest holder (free
AWJIA1617ZZ
FRONT SEAT
SE-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
PASSENGER SIDE : Removal and Installation
INFOID:0000000011280454
REMOVAL
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seatback repair. It can lead to
personal injury if the side air bag module should accidentally deploy.
CAUTION:
• When removing or installing the seat trim, handle it carefully to keep dirt out and to avoid damage.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag module to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After front side air bag module inflates, the front seatback assembly must be replaced.
• When removing and installing the seat, use shop cloths to protect components from damage.
• Before removing the front seat, turn the ignition switch OFF, disconnect both battery cables then
wait at least three minutes.
1. Slide the seat to the full rearward position.
2. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
3. Disconnect harness connector from side air bag module.
4. Remove front bolts.
5. Connect negative and positive battery terminals, then slide the seat to the full forward position. Refer to
PG-80, "Removal and Installation"
6. Slide the seat to the full forward position.
7. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
8. Remove rear bolts.
9. Tilt the seat rearward and disconnect the harness connectors from the seat.
NOTE:
Take note of harness routing and attachment locations for correct installation.
10. Remove the seat from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
WARNING:
• Perform additional services when installing front passenger seat. Refer to
SERVICE WHEN REPLACING CONTROL UNIT : Description"
• Zero point reset must be performed every time the front passenger seat is removed from the vehicle.
• Zero point reset is done after the front passenger seat is installed in vehicle and all bolts are tight-
ened to specification.
1.
Headrest
2.
Seatback board
3.
Seatback support
4.
Seatback heater (if equipped)
5.
Seatback trim
6.
Seatback pad
7.
Seat cushion trim
8.
Seat cushion pad
9.
Seat cushion heater (if
equipped)
10. Seat cushion support
11. Seat cushion silencer
12. Seat harness
13. Occupant classification system
harness
14. Seat cushion outer finisher
(LH)
15. Seat cushion inner finisher (LH)
16. Occupant classification system
sensor
17. Occupant classification sys-
tem control unit
18. Occupant classification system
control unit bracket
19. Wiring harness bracket
20. Seat cushion outer finisher
21. Recline lever
22. Seat cushion inner finisher (RH) 23. Seat cushion rear finisher
(RH)
24. Side air bag module (not service-
able)
25. Seat cushion frame
26. Seat belt buckle
27. Seat cushion rear finisher (LH)
28. Seatback frame
29. Seatback bracket
30. Headrest holder (free)
31. Headrest holder (locking)
SE-36
< REMOVAL AND INSTALLATION >
FRONT SEAT
CAUTION:
Make sure that the seat harness or the floor carpet is not damaged during installation.
NOTE:
• When installing the front seat (RH), tighten the bolts in the order
shown.
• Tighten the seat bolts to specification. Refer to
.
ALJIA0789ZZ
SECOND ROW SEATS
SE-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
SECOND ROW SEATS
Exploded View
INFOID:0000000011280455
RH SEAT
AWJIA1618ZZ
1.
Headrest
2.
Seatback upper luggage board
3.
Seatback luggage board
4.
Seatback trim
5.
Seatback pad
6.
Seatback pad wire
7.
Recline release cable
8.
Seat cushion trim
9.
Fold flat strap
10. Seat cushion pad
11. Seat cushion silencer
12. Seat cushion pad wire
13. Bolt cover
14. Seat cushion outer finisher (RH) 15. Seat cushion inner finisher (RH)
16. Seat cushion frame
17. Seat cushion frame
18. Seat cushion slide (RH)
19. Seat cushion slide cable
20. Rear bolt cover (RH) (with third
row seat)
21. Front bolt cover (RH)
22. Front bolt cover (LH)
23. Rear bolt cover (LH) (with third
row seat)
24. Seat cushion slide (LH)
25. Seat cushion inner finisher (LH) 26. Seat cushion outer finisher (LH) 27. Seat cushion rear finisher (LH)
28. Seat belt buckle
29. Recline lever finisher
30. Seatback frame
31. Recline device
32. Recline device cover
33. Headrest holder (locked)
34. Headrest holder (free)
Clip
Pawl
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст