Nissan Rogue. Instruction — part 1178
TM-84
< BASIC INSPECTION >
[CVT: RE0F10D]
ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY
With CONSULT
1. Select “WORK SUPPORT” in “TRANSMISSION”.
2. Select “CONFORM CVTF DETERIORTN”.
3. Touch “Clear”.
>> WORK END
ADDITIONAL SERVICE WHEN REPLACING TCM AND TRANSAXLE ASSEM-
BLY
TM-85
< BASIC INSPECTION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ADDITIONAL SERVICE WHEN REPLACING TCM AND TRANSAXLE AS-
SEMBLY
Description
INFOID:0000000011279300
When replacing TCM and transaxle assembly simultaneously, perform the following work.
TCM PROGRAMMING
• Since vehicle specifications are not yet written in a new TCM, it is necessary to write them with CONSULT.
CAUTION:
When replacing TCM, save TCM data on CONSULT before removing TCM.
WRITING TCM DATA
• TCM performs accurate control by retrieving data (inherent characteristic value) of each solenoid. For this
reason, after replacing TCM and transaxle assembly, it is necessary to write new data in TCM.
Work Procedure
INFOID:0000000011279301
1.
SAVE TCM DATA (VEHICLE SPECIFICATIONS)
With CONSULT
1. Turn ignition switch OFF.
2. Turn ignition switch ON.
3. Select “Re/programming, Configuration”.
4. Select “AT/CVT”.
NOTE:
If “AT/CVT” is not displayed and TCM data cannot be saved on CONSULT, GO TO 2.
5. Select “Programming”.
6. Save TCM data on CONSULT according to the CONSULT display.
>> GO TO 2.
2.
REPLACE TCM AND TRANSAXLE ASSEMBLY
1. Turn ignition switch OFF and wait for 10 seconds.
2. Replace TCM and transaxle assembly. Refer to
TM-202, "Removal and Installation"
(Transaxle assembly).
>> GO TO 3.
3.
WRITE TCM DATA (VEHICLE SPECIFICATIONS)
With CONSULT
1. Select “Programming”.
2. Perform programming according to the CONSULT display.
>> GO TO 4.
4.
CHECK THE SERIAL NUMBER
TM-86
< BASIC INSPECTION >
[CVT: RE0F10D]
ADDITIONAL SERVICE WHEN REPLACING TCM AND TRANSAXLE ASSEM-
BLY
Write down the serial number of new transaxle assembly.
>> GO TO 5.
5.
WRITE TCM DATA (IP CHARACTERISTICS VALUE)
NOTE:
Write data of new solenoid in TCM according to the following instructions:
With CONSULT
CAUTION:
When the work is interrupted, obtain data again from the supplied CD.
1. Shift the selector lever to the P position.
2. Turn ignition switch OFF and wait for 10 seconds.
3. Turn ignition switch ON.
4. Insert the supplied CD into CONSULT.
5. Select “Work Support” in “TRANSMISSION”.
6. Select “WRITE IP CHARA - REPLACEMENT AT/CVT”.
7. Check that the serial number displayed on CONSULT screen and those written in the memo agree.
8. Write data in TCM according to the instructions on the CONSULT screen.
NOTE:
When writing is complete, the shift position indicator of the combination meter displays P.
>> WORK END
JSDIA6075GB
CVT FLUID COOLER SYSTEM
TM-87
< BASIC INSPECTION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CVT FLUID COOLER SYSTEM
Cleaning
INFOID:0000000011279302
Whenever an automatic transaxle is repaired, overhauled, or replaced, the CVT fluid cooler mounted in the
radiator must be inspected and cleaned.
Metal debris and friction material, if present, can be trapped or be deposited in the CVT fluid cooler. This
debris can contaminate the newly serviced CVT or, in severe cases, can block or restrict the flow of CVT fluid.
In either case, malfunction of the newly serviced CVT may occur.
Debris, if present, may deposit as CVT fluid enters the cooler inlet. It will be necessary to back flush the cooler
through the cooler outlet in order to flush out any built up debris.
CVT FLUID COOLER CLEANING PROCEDURE
1. Position an oil pan under the transaxle's inlet and outlet cooler hoses.
2. Identify the inlet and outlet fluid cooler hoses.
3. Disconnect the fluid cooler inlet and outlet rubber hoses from the
steel cooler tubes or bypass valve.
NOTE:
Replace the cooler hoses if rubber material from the hose
remains on the tube fitting.
4. Allow any CVT fluid that remains in the cooler hoses to drain into
the oil pan.
5. Insert the extension adapter hose of a can of Transmission
Cooler Cleaner (Nissan P/N 999MP-AM006) into the cooler out-
let hose.
CAUTION:
• Wear safety glasses and rubber gloves when spraying the
Transmission Cooler Cleaner.
• Spray Transmission Cooler Cleaner only with adequate
ventilation.
• Avoid contact with eyes and skin.
• Never breath vapors or spray mist.
6. Hold the hose and can as high as possible and spray Transmis-
sion Cooler Cleaner in a continuous stream into the cooler outlet
hose until CVT fluid flows out of the cooler inlet hose for 5 seconds.
7. Insert the tip of an air gun into the end of the cooler outlet hose.
8. Wrap a shop rag around the air gun tip and end of the cooler
outlet hose.
9. Blow compressed air regulated to 5 to 9 kg/cm
2
(70 to 130 psi)
through the cooler outlet hose for 10 seconds to force out any
remaining CVT fluid.
10. Repeat steps 5 through 9 three additional times.
11. Position an oil pan under the banjo bolts that connect the CVT
fluid cooler steel lines to the transaxle.
12. Remove the banjo bolts.
13. Flush each steel line from the cooler side back toward the tran-
saxle by spraying Transmission Cooler Cleaner in a continuous stream for 5 seconds.
14. Blow compressed air regulated to 5 to 9 kg/cm
2
(70 to 130 psi) through each steel line from the cooler
side back toward the transaxle for 10 seconds to force out any remaining CVT fluid.
15. Ensure all debris is removed from the steel cooler lines.
16. Ensure all debris is removed from the banjo bolts and fittings.
SCIA4421E
SCIA4422E
SCIA4423E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст