Nissan Rogue. Instruction — part 1239
WT-32
< DTC/CIRCUIT DIAGNOSIS >
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
YES
>> Perform DTC CONFIRMATION PROCEDURE again. Refer to
NO
>> GO TO 3.
3.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1. Adjust tire pressure for all wheels to the specified value. Refer to
.
2. Select “Data Monitor” in “AIR PRESSURE MONITOR”.
3. Check that the air pressures match the specified value.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace malfunctioning components.
Monitor item
Displayed value
AIR PRESS FL
Approximately equal to value indicated on tire gauge for front LH tire
AIR PRESS FR
Approximately equal to value indicated on tire gauge for front RH tire
AIR PRESS RR
Approximately equal to value indicated on tire gauge for rear RH tire
AIR PRESS RL
Approximately equal to value indicated on tire gauge for rear LH tire
C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)
WT-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)
DTC Logic
INFOID:0000000011280506
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech
II User Guide for additional information.
• Activate and display TPMS sensor IDs
• Display tire pressure reported by the TPMS sensor
• Read TPMS DTCs
• Register TPMS sensor IDs
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
1. Perform tire pressure sensor ID registration. Refer to
.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
NOTE:
Avoid driving in areas with radio interference.
3. Perform “Self Diagnostic Result”.
Is DTC C1708, C1709, C1710, or C1711 detected?
YES
>> Proceed to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280507
NOTE:
The Signal Tech II Tool [– (J-50190)] can be used to perform the following functions. Refer to the Signal Tech
II User Guide for additional information.
• Activate and display TPMS sensor IDs
• Display tire pressure reported by the TPMS sensor
• Read TPMS DTCs
• Register TPMS sensor IDs
Regarding Wiring Diagram information, refer to
.
1.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1. Select “Data Monitor” in “AIR PRESSURE MONITOR”.
2. Check that the air pressures match the specified value.
DTC
Display Item
Malfunction Detected Condition
Possible Cause
C1708
[NO - DATA] - FL
Data signal from the front LH wheel tire pres-
sure sensor cannot be detected.
• Driving in area with radio interference.
• ID registration incomplete
• Tire pressure sensor
• Harness or connectors
• BCM
C1709
[NO - DATA] - FR
Data signal from the front RH wheel tire pres-
sure sensor cannot be detected.
C1710
[NO - DATA] - RR
Data signal from the rear RH wheel tire pres-
sure sensor cannot be detected.
C1711
[NO - DATA] - RL
Data signal from the rear LH wheel tire pres-
sure sensor cannot be detected.
WT-34
< DTC/CIRCUIT DIAGNOSIS >
C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)
Are all tire pressures displayed 0 kPa (psi)?
YES
>> GO TO 2.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-68, "Removal and Installation"
2.
CHECK BCM POWER CIRCUIT
Check voltage between BCM connector M20 terminal 161 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK BCM GROUND CIRCUIT
Check continuity between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connectors.
4.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Can the tire pressure sensor ID registration be completed?
YES
>> GO TO 5.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-68, "Removal and Installation"
5.
RECHECK TIRE PRESSURE SIGNAL
With CONSULT
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
2. Select “Data Monitor” in “AIR PRESSURE MONITOR”.
3. Check that the air pressures match the specified value.
Does Data Monitor display specified value without turning tire pressure warning lamp ON?
YES
>> Inspection End.
Monitor item
Displayed value
AIR PRESS FL
Approximately equal to specified value. Refer to
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
BCM
Ground
Voltage
(Approx.)
Connector
Terminal
M20
161
—
Battery voltage
BCM
Ground
Continuity
Connector
Terminal
M20
170
—
Yes
171
Monitor item
Displayed value
AIR PRESS FL
Approximately equal to specified value. Refer to
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)
WT-35
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NO
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
(with Intelligent Key system) or
135, "Removal and Installation"
(without Intelligent Key system).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст