Nissan Rogue. Instruction — part 742
HA-36
< REMOVAL AND INSTALLATION >
COOLER PIPE AND HOSE
• Tighten bolts to specified torque. Refer to
• Do not reuse O-rings.
• Apply A/C oil to new O-rings for installation.
• After charging the refrigerant, check for leaks. Refer to
CONDENSER
HA-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
CONDENSER
Exploded View
INFOID:0000000011279498
CONDENSER
CONDENSER : Removal and Installation
INFOID:0000000011279499
REMOVAL
CAUTION:
Before servicing, turn the ignition switch off, disconnect both battery cables and wait at least three
minutes.
1. Disconnect the negative and positive battle terminals and wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
2. Discharge the refrigerant. Refer to
3. Remove front air duct. Refer to
EM-26, "Removal and Installation"
4. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
5. Remove front combination lamp (RH). Refer to
EXL-119, "Removal and Installation"
.
6. Remove air guides (LH/RH). Refer to
7. Remove crash zone sensor. Refer to
SR-22, "Removal and Installation"
.
8. Disconnect the harness connector from the refrigerant pressure sensor.
9. Remove the bolt (A) that retains the high-pressure flexible hose
(2) to the condenser (1).
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
1.
Air guide (LH)
2.
Condenser upper bracket (LH)
3.
Condenser (includes liquid tank)
4.
Condenser upper bracket (RH)
5.
Air guide (RH)
6.
Refrigerant pressure sensor
7.
O-ring
8.
Condenser lower bracket (RH)
9.
Condenser lower bracket (LH)
AWIIA1872ZZ
ALIIA0937ZZ
HA-38
< REMOVAL AND INSTALLATION >
CONDENSER
10. Remove bolt (A) that retains high-pressure pipe (1) to condenser
(2).
11. Remove the condenser bracket bolts and condenser.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten bolts to specification. Refer to
.
• Do not reuse O-rings.
• Apply A/C oil to new O-rings for installation.
• After charging the refrigerant, check for leaks. Refer to
LIQUID TANK
LIQUID TANK : Removal and Installation
INFOID:0000000011279500
The liquid tank is serviced as an assembly with the condenser. Refer to
HA-37, "CONDENSER : Removal and
REFRIGERANT PRESSURE SENSOR
REFRIGERANT PRESSURE SENSOR : Removal and Installation
INFOID:0000000011279501
REMOVAL
1. Discharge the refrigerant. Refer to
2. Remove front air duct. Refer to
EM-26, "Removal and Installation"
3. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
4. Remove air guide (RH). Refer to
.
5. Disconnect the harness connector from the refrigerant pressure sensor and remove.
CAUTION:
Cap or wrap the opening of the refrigerant pressure sensor with suitable material such as vinyl
tape to avoid the entry of air.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply A/C oil to new O-rings for installation.
• After charging the refrigerant, check for leaks. Refer to
ALIIA0938ZZ
HEATING AND COOLING UNIT ASSEMBLY
HA-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
HEATING AND COOLING UNIT ASSEMBLY
Exploded View
INFOID:0000000011279502
Steering Member
AWIIA1801ZZ
1.
Heating and cooling unit assembly
2.
Steering member
A.
Bolt
B.
Nut
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст