Nissan Rogue. Instruction — part 129
BCS-122
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
INSPECTION AND ADJUSTMENT
>> Work End.
3.
PERFORM “AFTER REPLACE ECU” OR “MANUAL CONFIGURATION”
CONSULT
1. Select “After Replace ECU” or “Instruction Configuration”.
2. Identify the correct model and configuration list. Refer to
BCS-122, "CONFIGURATION (BCM) : Configu-
3. Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
4. Select “Next”.
CAUTION:
Make sure to select “Next”, confirm each setting value and press “OK” even if the indicated con-
figuration of brand new BCM is same as the desirable configuration. If not, configuration which is
set automatically by selecting vehicle model cannot be memorized.
5. When "Completed", select "End".
>> GO TO 4.
4.
OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> Work End.
CONFIGURATION (BCM) : Configuration List
INFOID:0000000011280266
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal
control of ECU.
⇔: Items which confirm vehicle specifications
MANUAL SETTING ITEM
Items
Setting value
I-KEY
WITH
⇔ WITHOUT
DTRL
WITH
⇔ WITHOUT
AUTO DOOR UNLOCK TIMING
WITH I-KEY
⇔ W/O I-KEY
BCS
SHIPPING MODE CANCEL OPERATION
BCS-123
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SHIPPING MODE CANCEL OPERATION
Work Procedure
INFOID:0000000011280267
1.
SHIPPING MODE CANCEL OPERATION
1. Turn ignition switch OFF.
2. Push in (switch on) the extended storage fuse switch. Refer to
3. Turn ignition switch ON.
4. Turn ignition switch OFF and wait at least 2 seconds.
>> GO TO 2.
2.
SHIPPING MODE CANCEL CHECK
1. Turn ignition switch ON.
2. Check that extended storage fuse warning message is not displayed on information display.
>> Work End.
BCS-124
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
U1000 CAN COMM CIRCUIT
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000011280268
.
DTC Logic
INFOID:0000000011280269
DTC DETECTION LOGIC
NOTE:
U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm
that there are actual CAN diagnostic symptoms and a present DTC by performing the Self Diagnostic Result
procedure.
Diagnosis Procedure
INFOID:0000000011280270
1.
PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 second or more.
2. Check “Self Diagnostic Result”.
Is “CAN COMM CIRCUIT” displayed?
YES
>> Perform CAN Diagnosis as described in DIAGNOSIS section of CONSULT Operation Instruction.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
CONSULT Display
DTC Detection Condition
Possible cause
CAN COMM CIRCUIT
[U1000]
When any listed module cannot communicate with CAN
communication signal continuously for 2 seconds or
more with ignition switch ON.
In CAN communication system, any item (or items)
of the following listed below is malfunctioning:
• Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)
BCS
U1010 CONTROL UNIT (CAN)
BCS-125
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
U1010 CONTROL UNIT (CAN)
DTC Logic
INFOID:0000000011280271
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011280272
1.
REPLACE BCM
When DTC U1010 is detected, replace BCM.
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
CONSULT Display
DTC Detection Condition
Possible Cause
CAN COMM CIRCUIT
[U1010]
BCM detected internal CAN communication circuit mal-
function.
BCM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст