Nissan Rogue. Instruction — part 178
EXCESSIVE OPERATION FREQUENCY
BRC-123
< SYMPTOM DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
With CONSULT
1. Turn the ignition switch OFF
→ ON.
CAUTION:
• Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
• Set the vehicle to READY/Start the engine.
2. Repeat step 1 two or more times.
3. Perform “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> Inspection End.
BRC-124
< SYMPTOM DIAGNOSIS >
[VDC/TCS/ABS]
UNEXPECTED BRAKE PEDAL REACTION
UNEXPECTED BRAKE PEDAL REACTION
Description
INFOID:0000000011280659
A malfunction of brake pedal feel (height or others) is detected when brake pedal is depressed.
Diagnosis Procedure
INFOID:0000000011280660
1.
CHECK FRONT AND REAR AXLE
Check that there is no excessive looseness in front and rear axle.
• 2WD: Refer to
(rear).
• AWD: Refer to
(rear).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK DISC ROTOR
Check disc rotor runout.
• Front: Refer to
BR-11, "DISC BRAKE ROTOR : Inspection"
.
• Rear: Refer to
BR-13, "DISC BRAKE ROTOR : Inspection"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Refinish the disc rotor.
3.
CHECK BRAKE FLUID LEAKAGE
Check fluid leakage.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK BRAKE PEDAL
Check each item of brake pedal. Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Adjust each item of brake pedal. Refer to
.
5.
CHECK BRAKING FORCE
Check brake force using a brake tester.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Check each components of brake system.
6.
CHECK BRAKE PERFORMANCE
Disconnect ABS actuator and electric unit (control unit) connector so that ABS does not operate. Check that
brake force is normal in this condition. Connect harness connectors after checking.
Is the inspection result normal?
YES
>> Normal
NO
>> Check each components of brake system.
THE BRAKING DISTANCE IS LONG
BRC-125
< SYMPTOM DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
THE BRAKING DISTANCE IS LONG
Description
INFOID:0000000011280661
Brake stopping distance is long when ABS function is operated.
Diagnosis Procedure
INFOID:0000000011280662
CAUTION:
Brake stopping distance on slippery road like rough road, gravel road or snowy road may become
longer when ABS is operated than when ABS is not operated.
1.
CHECK BRAKING FORCE
Check brake force using a brake tester.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check each components of brake system.
2.
CHECK BRAKE PERFORMANCE
Disconnect ABS actuator and electric unit (control unit) connector so that ABS does not operate. Check brake
stopping distance in this condition. Connect harness connectors after checking.
Is the inspection result normal?
YES
>> Normal
NO
>> Check each components of brake system.
BRC-126
< SYMPTOM DIAGNOSIS >
[VDC/TCS/ABS]
DOES NOT OPERATE
DOES NOT OPERATE
Description
INFOID:0000000011280663
VDC function, TCS function, ABS function, EBD function, Brake limited slip differential (BLSD) function, Brake
assist function, hill start assist function or Brake force distribution function does not operate.
Diagnosis Procedure
INFOID:0000000011280664
CAUTION:
• VDC function, TCS function, ABS function, EBD function, Brake limited slip differential (BLSD) func-
tion, Brake assist function, hill start assist function and Brake force distribution function never oper-
ate when the vehicle speed is 10 km/h (6.2 MPH) or less. However, TCS function, Brake limited slip
differential (BLSD) function and hill start assist function operates when the vehicle speed is 0 km/h
(0 MPH) (the vehicle is in stop status).
• VDC function and TCS function never operate when VDC OFF switch is operated (when VDC OFF
indicator lamp turns ON).
1.
CHECK ABS WARNING LAMP
Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn ON and turn OFF approx. 1
second after key switch is turned ON. Check that ABS warning lamp, brake warning lamp and VDC warning
lamp and stay in OFF status during driving.
CAUTION:
Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake
fluid is less than the specified level (brake fluid level switch is ON).
Is the inspection result normal?
YES
>> Normal
NO
>> GO TO 2.
2.
PERFORM SELF DIAGNOSTIC
With CONSULT
1. Turn the ignition switch OFF
→ ON.
CAUTION:
• Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
• Start the engine.
2. Repeat step 1 two or more times.
3. Perform “Self Diagnostic Result” of “ABS” with CONSULT.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> Inspection End.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст