Nissan Rogue. Instruction — part 470
EC-148
< BASIC INSPECTION >
[QR25DE]
HOW TO SET SRT CODE
HOW TO SET SRT CODE
Description
INFOID:0000000011277908
OUTLINE
In order to set all SRTs, the self-diagnoses as in the “SRT ITEM” table must have been performed at least
once. Each diagnosis may require actual driving for a long period of time under various conditions.
SRT ITEM
The table below shows required self-diagnostic items to set the SRT to “CMPLT”.
*1: Though displayed on the CONSULT screen, “HO2S HTR” is not SRT item.
*2: If completion of several SRTs is required, perform driving patterns (DTC confirmation procedure), one by
one based on the priority for models with CONSULT.
SRT SERVICE PROCEDURE
SRT item
*1
(CONSULT indication)
Performance
Priority
*2
Required self-diagnostic items to set the SRT to “CMPLT”
Corresponding
DTC No.
CATALYST
1
Three way catalyst function
P0420
EVAP SYSTEM
1
EVAP control system purge flow monitoring
P0441
1
EVAP control system
P0456
HO2S
1
Air fuel ratio (A/F) sensor 1
P014C, P014D,
P015A, P015B
Heated oxygen sensor 2
P0137
Heated oxygen sensor 2
P0138
Heated oxygen sensor 2
P0139
EGR/VVT SYSTEM
2
Intake value timing control function
P0011, P052A,
P052B
HOW TO SET SRT CODE
EC-149
< BASIC INSPECTION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
If a vehicle has failed the state emissions inspection due to one or more SRT items indicating “INCMP”, review
the flowchart diagnostic sequence, referring to the following flowchart.
SRT Set Driving Pattern
INFOID:0000000011277909
CAUTION:
JSBIA0400GB
EC-150
< BASIC INSPECTION >
[QR25DE]
HOW TO SET SRT CODE
Always drive the vehicle in safe manner according to traffic conditions and obey all traffic laws.
*1: Depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH), then release the accelerator pedal
and keep it released for more than 10 seconds. Depress the accelerator pedal until vehicle speed is 90 km/h
(56 MPH) again.
*2: Checking the vehicle speed with GST is advised.
• The time required for each diagnosis varies with road surface conditions, weather, altitude, individual driving
habits, etc.
• “Zone A” is the fastest time where required for the diagnosis under normal conditions*. If the diagnosis is not
completed within “Zone A”, the diagnosis can still be performed within “Zone B”.
JPBIA5560GB
HOW TO SET SRT CODE
EC-151
< BASIC INSPECTION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
*: Normal conditions
- Sea level
- Flat road
- Ambient air temperature: 20 – 30
°C (68 – 86°F)
NOTE:
Diagnosis is performed as quickly as possible under normal conditions. However, under other conditions,
diagnosis may also be performed. [For example: ambient air temperature other than 20 – 30
°C (68 – 86°F)]
Work Procedure
INFOID:0000000011277910
1.
CHECK DTC
Check DTC.
Is any DTC detected?
YES
>> Repair malfunction(s) and erase DTC. Refer to
NO
>> GO TO 2.
2.
CHECK SRT STATUS
With CONSULT
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT.
Without CONSULT
Perform “SRT status” mode with
EC-66, "On Board Diagnosis Function"
With GST
Select Service $01 with GST.
Is SRT code(s) set?
YES
>> GO TO 11.
NO-1 >> With CONSULT: GO TO 3.
NO-2 >> Without CONSULT: GO TO 4.
3.
DTC CONFIRMATION PROCEDURE
1. Select “SRT WORK SUPPORT” in “DTC & SRT CONFIRMATION” mode with CONSULT.
2. For SRT(s) that is not set, perform the corresponding “DTC CONFIRMATION PROCEDURE” according to
the “Performance Priority” in the “SRT ITEM” table. Refer to
.
3. Check DTC.
Is any DTC detected?
YES
>> Repair malfunction(s) and erase DTC. Refer to
NO
>> GO TO 10.
4.
PERFORM ROAD TEST
• Check the “Performance Priority” in the “SRT ITEM” table. Refer to
• Perform the most efficient SRT set driving pattern to set the SRT properly. Refer to
.
In order to set all SRTs, the SRT set driving pattern must be performed at least once.
>> GO TO 5.
5.
PATTERN 1
1. Check the vehicle condition;
-
Engine coolant temperature is
−10 to 35°C (14 to 95°F).
-
Fuel tank temperature is more than 0
°C (32°F).
2. Start the engine.
3. Keep engine idling until the engine coolant temperature is greater than 70
°C (158°F)
NOTE:
ECM terminal voltage is follows;
• Engine coolant temperature
-
−10 to 35°C (14 to 95°F): 3.0 – 4.3 V
- 70
°(158°F): Less than 4.1 V
• Fuel tank temperature: Less than 1.4 V
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст