Nissan Rogue. Instruction — part 845
LAN
B2600-55 CONFIG ERROR
LAN-79
< DTC/CIRCUIT DIAGNOSIS >
[CAN GATEWAY]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B2600-55 CONFIG ERROR
DTC Description
INFOID:0000000011277557
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Configuration is incomplete
• BCM
FAIL-SAFE
Transmission and reception of the signal between CAN communication circuit 1 and CAN communication cir-
cuit 2 are stopped
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn ignition switch ON and wait at least 2 seconds or more.
2. Select “Self Diagnostic Result” mode of “CAN GATEWAY” using CONSULT.
3. Check DTC.
Is DTC B2600-55 detected?
YES
>> Proceed to
.
NO-1 >> To check malfunction symptom before repair:
GI-44, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000011277558
1.
PERFORM CONFIGURATION OF CAN GATEWAY
Perform CAN gateway configuration. Refer to
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
1. Turn ignition switch ON.
2. Perform DTC confirmation procedure again. Refer to
.
3. Check DTC.
Is DTC B2600-55 detected again?
YES
>> Replace BCM. Refer to the following.
• With Intelligent Key system:
BCS-75, "Removal and Installation"
• Without Intelligent Key system:
BCS-135, "Removal and Installation"
.
NO
>> INSPECTION END
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B2600-55
CONFIG ERROR
(Configuration error)
When no data are stored in the BCM (CAN gateway function).
LAN-80
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 1)]
MAIN LINE BETWEEN IPDM-E AND DLC CIRCUIT
DTC/CIRCUIT DIAGNOSIS
MAIN LINE BETWEEN IPDM-E AND DLC CIRCUIT
Diagnosis Procedure
INFOID:0000000011506661
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).
-
Harness connector E152
-
Harness connector M31
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Disconnect the following harness connectors.
-
IPDM E/R
-
Harness connectors E152 and M31
2. Check the continuity between the IPDM E/R harness connector and the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the main line between the IPDM E/R and the harness connector E152.
3.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
Check the continuity between the harness connector and the data link connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the IPDM E/R and the data link connector.
NO
>> Repair the main line between the harness connector M31 and the data link connector.
IPDM E/R harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E120
24
E152
61J
Existed
22
60J
Existed
Harness connector
Data link connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M31
61J
M22
6
Existed
60J
14
Existed
LAN
MAIN LINE BETWEEN DLC AND CCM CIRCUIT
LAN-81
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 1)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
MAIN LINE BETWEEN DLC AND CCM CIRCUIT
Diagnosis Procedure
INFOID:0000000011506662
1.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect the following harness connectors.
-
ECM
-
Chassis control module
4. Check the continuity between the data link connector and the chassis control module harness connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the data link connector and the chassis con-
trol module.
NO
>> Repair the main line between the data link connector and the chassis control module.
Data link connector
Chassis control module harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M22
6
M96
4
Existed
14
3
Existed
LAN-82
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 1)]
ECM BRANCH LINE CIRCUIT
ECM BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000011506665
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the ECM for damage, bend and loose connection (unit side and
connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of ECM.
2. Check the resistance between the ECM harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the ECM branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the ECM. Refer to
Is the inspection result normal?
YES (Present error)>>Replace the ECM. Refer to
EC-502, "Removal and Installation"
YES (Past error)>>Error was detected in the ECM branch line.
NO
>> Repair the power supply and the ground circuit.
ECM harness connector
Resistance (
Ω)
Connector No.
Terminal No.
E16
100
99
Approx. 108 – 132
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст