Nissan Titan A60. Instruction — part 578
CONDENSER
HA-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
CONDENSER
Removal and Installation for Condenser
INFOID:0000000006163117
REMOVAL
1. Discharge the refrigerant. Refer to
HA-29, "HFC-134a (R-134a) Service Procedure"
.
2. Remove the radiator. Refer to
CO-16, "Removal and Installation"
.
CAUTION:
Be careful not to damage the core surface of the condenser and the radiator.
3. Disconnect the high-pressure flexible hose and the high-pressure pipe from the condenser.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
4. Disconnect the refrigerant pressure sensor connector.
• Remove the refrigerant pressure sensor from the condenser
as necessary.
5. Lift the condenser out of the mounting grommets to remove the
condenser.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-rings of the high-pressure pipe, refrigerant pressure sensor, and high-pressure flexi-
ble hose with new ones, then apply compressor oil to them when installing them.
• After charging refrigerant, check for leaks.
• Replace the grommets as necessary.
LJIA0145E
HA-42
< REMOVAL AND INSTALLATION >
REFRIGERANT PRESSURE SENSOR
REFRIGERANT PRESSURE SENSOR
Removal and Installation for Refrigerant Pressure Sensor
INFOID:0000000006163118
REMOVAL
1. Discharge the refrigerant. Refer to
HA-29, "HFC-134a (R-134a) Service Procedure"
.
2. Disconnect the refrigerant pressure sensor electrical connector
and remove the refrigerant pressure sensor from the condenser.
CAUTION:
Be careful not to damage the condenser fins.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to damage the condenser fins.
• Replace the O-ring of the refrigerant pressure sensor with a new one, then apply compressor oil to it
when installing it.
• After charging refrigerant, check for leaks.
LJIA0145E
EXPANSION VALVE
HA-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
EXPANSION VALVE
Removal and Installation for Expansion Valve
INFOID:0000000006163119
REMOVAL
1. Discharge the refrigerant. Refer to
HA-29, "HFC-134a (R-134a) Service Procedure"
.
2. Remove the evaporator. Refer to
VTL-27, "Removal and Installation for Evaporator"
3. Remove the cooler grommet.
4. Remove the expansion valve.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-rings on the A/C refrigerant pipes with new ones, then apply compressor oil to them
when installing them.
• After charging refrigerant, check for leaks.
WJIA0582E
Expansion valve bolts
: 4 N·m (0.41 kg-m, 35 in-lb)
A/C refrigerant pipe to expansion valve bolt
: Refer to
HA-44
< REMOVAL AND INSTALLATION >
LIQUID TANK
LIQUID TANK
Removal and Installation of Liquid Tank
INFOID:0000000006713222
REMOVAL
1. Remove the condenser. Refer to
HA-41, "Removal and Installation for Condenser"
.
2. Clean liquid tank and its surrounding area, and remove dirt and rust from liquid tank.
CAUTION:
Be sure to clean carefully.
3. Remove bracket bolt (A) and liquid tank attachment bolt (B) from
liquid tank (1) at the condenser mounting block.
4. Remove liquid tank bracket (1) from protruding part of con-
denser (2).
5. Slide liquid tank (3) upward away from condenser mounting
block, and remove liquid tank (3).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Be careful to align the threaded liquid tank attachment bolt hole (A)
with condenser mounting block hole (B).
CAUTION:
• Make sure liquid tank attachment bolt is securely installed at
condenser mounting block (B).
• Always replace O-rings for A/C piping and liquid tank with
new ones, and apply compressor oil when installing.
• When recharging refrigerant, check for leaks. Refer to
"Checking System for Leaks Using the Fluorescent Dye Leak
.
ALIIA0403ZZ
ALIIA0404ZZ
ALIIA0405ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст