Nissan Titan A60. Instruction — part 469
CAMSHAFT
EM-61
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
c. Remove the bolts and the chain tensioner (RH) (A).
NOTE:
If it is difficult to push plunger on chain tensioner (RH) (A),
remove the plunger under extended condition.
14. Loosen camshaft sprocket bolts as shown and remove camshaft
sprockets.
CAUTION:
To avoid interference between valves and pistons, do not
turn crankshaft or camshaft with timing chain discon-
nected.
15. Remove the RH (A) front cover bolts and the LH (B) front cover
bolts.
16. Remove RH (A) camshaft bracket bolts and LH (C) camshaft
bracket bolts in the reverse of order shown to remove camshaft
brackets.
• Remove No. 1 camshaft bracket.
NOTE:
The bottom and front surface of bracket will be stuck because
of liquid gasket.
•
⇐: Engine front
• B: Exhaust side
• D: Intake side
WBIA0705E
KBIA2485E
WBIA0706E
WBIA0707E
EM-62
< REMOVAL AND INSTALLATION >
CAMSHAFT
17. Remove the camshaft.
18. Remove the valve lifters if necessary.
• Correctly identify location where each part is removed from. Keep parts organized to avoid mixing them
up.
INSPECTION AFTER REMOVAL
Camshaft Runout
1. Put V block on precise flat work bench, and support No. 1 and
No. 5 journals of the camshaft.
2. Set dial indicator vertically to No. 3 journal.
3. Turn the camshaft to one direction, and measure the camshaft
runout on dial indicator (total indicator reading).
• If measurement exceeds specification, replace the camshaft.
Camshaft Cam Height
• Measure the camshaft cam height.
• If measurement is not within the specifications, replace the cam-
shaft.
Camshaft Journal Clearance
Camshaft Journal Diameter
• Measure the diameter of the camshaft journal.
Camshaft Bracket Inner Diameter
• Tighten the camshaft bracket bolt to the specified torque.
• Measure the inner diameter (A) of the camshaft bracket.
Calculation of Camshaft Journal Clearance
(Journal clearance) = (camshaft bracket inner diameter) – (camshaft
journal diameter)
• If measurement is not within specification, replace either or both
camshaft and cylinder head.
Camshaft runout
: Less than 0.02 mm (0.0008 in)
EMK0641D
Standard cam height
(intake)
: 44.865 - 45.055 mm
(1.7663 - 1.7738 in)
Standard cam height (ex-
haust)
: 45.075 - 45.265 mm
(1.7746 - 1.7821 in)
Cam wear limit
(intake & exhaust)
: 0.02 mm (0.0008 in)
PBIC0039E
Standard diameter : 25.950 - 25.970 mm
(1.0217 - 1.0224 in)
PBIC0040E
Standard
: 26.000 - 26.021 mm (1.0236 - 1.0244 in)
Standard
: 0.030 - 0.071 mm (0.0012 - 0.0028 in)
PBIC1645E
CAMSHAFT
EM-63
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
NOTE:
The inner diameter of the camshaft bracket is manufactured together with the cylinder head. Replace the
whole cylinder head as an assembly.
Camshaft End Play
• Install dial gauge in the thrust direction on the front end of the cam-
shaft. Measure the end play when the camshaft is moved forward/
backward (in direction to axis).
• If measurement is out of the specified range, replace the camshaft
and measure again.
• If measurement is still out of the specified range, replace the cylin-
der head.
• Measure the following parts if end play is outside the specified
value.
- Dimension
″A″ for camshaft No. 1 journal
- Dimension
″B″ for cylinder head No. 1 journal
• If measurements are not within specification, replace the camshaft
and/or cylinder head.
Camshaft Sprocket Runout
1. Install the camshaft in the cylinder head.
2. Install the camshaft sprocket to the camshaft.
3. Measure the camshaft sprocket runout.
• If measurement exceeds the specification, replace the cam-
shaft sprocket.
Valve Lifter
Check if the surface of the valve lifter has any wear or cracks.
• If any damage is found, replace the valve lifter.
• Select the thickness of the head so that the valve clearance is
within the standard when replacing. Refer to
.
Valve Lifter Clearance
Valve Lifter Diameter
Standard
: 0.115 - 0.188 mm (0.0045 - 0.0074 in)
PBIC0042E
Standard
: 30.500 - 30.548 mm (1.2008-1.2027 in)
Standard
: 30.360 - 30.385 mm (1.1953-1.1963 in)
KBIA2426J
Runout
: Less than 0.15 mm (0.0059 in)
KBIA0181J
KBIA0182E
EM-64
< REMOVAL AND INSTALLATION >
CAMSHAFT
• Measure the diameter of the valve lifter.
Valve Lifter Hole Diameter
• Measure the diameter of the valve lifter hole of the cylinder head,
using suitable tool.
Calculation of Valve Lifter Clearance
(Valve lifter clearance) = (valve lifter hole diameter) – (valve lifter
diameter)
• If the measurement is not within specification, referring to each
specification of the valve lifter diameter and hole diameter, replace
either or both the valve lifter and cylinder head.
INSTALLATION
1. Install the valve lifters if removed.
• Install removed parts in their original locations.
2. Install the camshafts. Use the table below for identification of the
RH and LH, and intake and exhaust.
• Install so that the RH bank (B) dowel pins (A) and LH bank (C)
dowel pins (A) at the front of the camshaft face are in the
direction shown.
Standard
: 33.977 - 33.987 mm (1.3377 - 1.3381 in)
JEM798G
Standard
: 34.000 - 34.016 mm (1.3386 - 1.3392 in)
Standard
: 0.013 - 0.039 mm (0.0005 - 0.0015 in)
PBIC0043E
Bank
INT EXH
Identification
paint (front)
Identification
paint (rear)
Identification
rib
RH
INT
Pink
—
Yes
EXH
—
Orange
Yes
LH
INT
Pink
—
No
EXH
—
Orange
No
KBIA2523E
WBIA0708E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст