Nissan Titan A60. Instruction — part 634
MAGNET CLUTCH
HAC-219
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL A/C (TYPE 2)]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
4.
CHECK MAGNET CLUTCH CIRCUIT
Check for operation sound when applying battery voltage direct cur-
rent to terminal.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
.
NO
>> Replace magnet clutch. Refer to
Installation for Compressor Clutch"
5.
CHECK BCM INPUT (COMPRESSOR ON) SIGNAL
Check compressor ON/OFF signal. Refer to
HAC-194, "CONSULT-III Function (BCM - AIR CONDITIONER)"
.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 6.
6.
CHECK CIRCUIT CONTINUITY BETWEEN BCM AND FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect BCM connector and front air control connector.
3. Check continuity between BCM harness connector M18 (A) ter-
minal 27 and front air control harness connector M176 (B) termi-
nal 12.
4. Check continuity between BCM harness connector M18 (A) ter-
minal 27 and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair harness or connector.
7.
CHECK VOLTAGE FOR FRONT AIR CONTROL (A/C COMPRESSOR ON SIGNAL)
1. Reconnect BCM connector and front air control connector.
2. Turn ignition switch ON.
3. Check voltage between front air control harness connector
M176 terminal 12 and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO-1 >> If the voltage is approx. 5V when A/C switch is ON, replace front air control. Refer to
.
SJIA0197E
A/C SW ON
: AIR COND SW ON
A/C SW OFF
: AIR COND SW OFF
27 - 12
Continuity should exist.
27 - ground
Continuity should not exist.
AWIIA0542ZZ
Terminals
Condition
Voltage
(+)
(-)
front air con-
trol connec-
tor
Terminal No.
M176
12
Ground
A/C switch: ON
Approx. 0V
A/C switch: OFF
Approx. 5V
AWIIA0543ZZ
HAC-220
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL A/C (TYPE 2)]
MAGNET CLUTCH
NO-2 >> If the voltage is approx. 0V when A/C switch is OFF, replace BCM. Refer to
.
8.
CHECK REFRIGERANT PRESSURE SENSOR
1. Start engine.
2. Check voltage between ECM harness connector F54 terminal
70 and ground.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Refer to
.
9.
CHECK BCM INPUT (FAN ON) SIGNAL
Check FAN ON/OFF signal. Refer to
HAC-194, "CONSULT-III Function (BCM - AIR CONDITIONER)"
.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> GO TO 10.
10.
CHECK CIRCUIT CONTINUITY BETWEEN BCM AND FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect BCM connector and front air control connector.
3. Check continuity between BCM harness connector M18 (A) ter-
minal 28 and front air control harness connector M177 (B) termi-
nal 36.
4. Check continuity between BCM harness connector M18 (A) ter-
minal 28 and ground.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair harness or connector.
11.
CHECK VOLTAGE FOR FRONT AIR CONTROL (FAN ON SIGNAL)
1. Reconnect BCM connector and front air control connector.
2. Turn ignition switch ON.
3. Check voltage between front air control harness connector
M177 terminal 36 and ground.
Terminals
Condition
Voltage
(+)
(-)
ECM con-
nector
Terminal No.
F54
70
Ground
A/C switch: ON
Approx. 0.36 - 3.88V
LJIA0124E
FRONT BLOWER CONTROL
DIAL ON
: FAN ON SIG ON
FRONT BLOWER CONTROL
DIAL OFF
: FAN ON SIG OFF
28 - 36
Continuity should exist.
28 - ground
Continuity should not exist.
AWIIA0544ZZ
AWIIA0545ZZ
MAGNET CLUTCH
HAC-221
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL A/C (TYPE 2)]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Is the inspection result normal?
YES
>> GO TO 12.
NO-1 >> If the voltage is approx. 5V when blower motor is ON, replace front air control. Refer to
.
NO-2 >> If the voltage is approx. 0V when blower motor is OFF, replace BCM. Refer to
.
12.
CHECK CAN COMMUNICATION
Check CAN communication. Refer to
• BCM – ECM
• ECM – IPDM E/R
• ECM – Front air control
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-28, "Removal and Installation of IPDM E/R"
.
NO
>> Repair or replace malfunctioning part(s).
Terminals
Condition
Voltage
(+)
(-)
front air con-
trol connector
Terminal No.
M177
36
Ground
A/C switch: ON
Blower motor
operates
Approx. 0V
A/C switch: OFF
Approx. 5V
HAC-222
< DTC/CIRCUIT DIAGNOSIS >
[MANUAL A/C (TYPE 2)]
WATER VALVE CIRCUIT
WATER VALVE CIRCUIT
Description
INFOID:0000000006164832
COMPONENT DESCRIPTION
Water Valve
The water valve (1) cuts the flow of engine coolant to the heater core
to allow for maximum cooling during A/C operation. It is controlled by
the front air control.
Water Valve Diagnosis Procedure
INFOID:0000000006164833
Regarding Wiring Diagram information, refer to
HAC-232, "Wiring Diagram - Instruction With 3 Control Dial Sys-
DIAGNOSTIC PROCEDURE FOR WATER VALVE
1.
CHECK WATER VALVE POWER AND GROUND CIRCUITS
1. Disconnect water valve connector F68.
2. Turn ignition switch ON.
3. Rotate temperature control dial to maximum heat.
4. Check voltage between water valve harness connector F68 ter-
minal 1 and terminal 2 while rotating temperature control dial to
maximum cold.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK WATER VALVE CONTROL OUTPUT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front air control connector M177.
3. Check continuity between water valve harness connector F68
(A) terminal 2 and front air control harness connector M177 (B)
terminal 30.
4. Check continuity between water valve harness connector F68
terminal 2 and ground.
Is the inspection result normal?
YES
>> Replace front air control. Refer to
VTL-8, "Removal and Installation"
.
WJIA1791E
Connector
Terminals
Condition
Voltage
(Approx.)
(+) (-)
Water valve: F68
2
1
Rotate temperature
control dial
Battery
voltage
WJIA1794E
2 - 30
: Continuity should exist.
2 - Ground
: Continuity should not exist.
AWIIA0546ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст