Nissan Titan A60. Instruction — part 883
SRC-48
< DTC/CIRCUIT DIAGNOSIS >
B1113 – B1115 SATELLITE SENSOR RH
2.
IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.
WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.
REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.
DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to
.
>> END
Diagnosis Procedure (Component Diagnosis)
INFOID:0000000006163175
Recheck SRS after each replacement.
1.
HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 2
2.
WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 3
3.
RH SIDE AIR BAG SATELLITE SENSOR
Replace the RH side air bag satellite sensor. Refer to
SR-13, "Removal and Installation"
.
>> GO TO 4
4.
AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to
SR-15, "Removal and Installation"
>> GO TO 5
5.
RELATED HARNESS
Replace the related harness.
B1113 – B1115 SATELLITE SENSOR RH
SRC-49
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
>> END
SRC-50
< DTC/CIRCUIT DIAGNOSIS >
B1XXX AIR BAG DIAGNOSIS SENSOR UNIT
B1XXX AIR BAG DIAGNOSIS SENSOR UNIT
Description
INFOID:0000000006163176
DTC B1XXX AIR BAG DIAGNOSIS SENSOR UNIT
The air bag diagnosis sensor unit will run self diagnostics when the ignition switch is turned ON. It has the
potential to set many diagnostic trouble codes which will conform to the B1XXX format, but will not match any
other SRS diagnostic trouble codes. Refer to
SRC-60, "Trouble Diagnosis with CONSULT-III"
.
PART LOCATION
SRC-7, "SRS Component Parts Location"
DTC Logic
INFOID:0000000006163177
DTC DETECTION LOGIC
With CONSULT-lll
Without CONSULT-lll
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES
>> Refer to
SRC-51, "Diagnosis Procedure (Component Diagnosis)"
.
NO
>> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
CONSULT-III name
DTC
DTC detecting condition
Repair order
CONTROL UNIT
B1XXX
Air bag diagnosis sensor unit is malfunc-
tioning.
1.
Visually check the wiring harness connection.
2.
Replace the harness if it has visible damage.
3.
Replace the air bag diagnosis sensor unit.
4.
Replace the related harness.
WHIA0198E
B1XXX AIR BAG DIAGNOSIS SENSOR UNIT
SRC-51
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
2.
IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.
WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.
REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.
DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to
.
>> END
Diagnosis Procedure (Component Diagnosis)
INFOID:0000000006163178
Recheck SRS after each replacement.
1.
HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 2
2.
WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 3
3.
AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to
SR-15, "Removal and Installation"
>> GO TO 4
4.
RELATED HARNESS
Replace the related harness.
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст