Nissan Titan A60. Instruction — part 951
TM-192
< REMOVAL AND INSTALLATION >
AIR BREATHER HOSE
4WD : 4WD: Removal and Installation
INFOID:0000000006736258
REMOVAL
INSTALLATION
CAUTION:
Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
1. Install each air breather hose into the breather tube (4). Set
each air breather hose with paint mark facing upward.
• A/T breather hose (1)
• Transfer breather hose (2)
• Actuator/transfer motor breather hose (3)
• Paint marks (A)
2. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (A) with the paint mark (B) facing
upward.
•
:Front
AWDIA0010ZZ
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Actuator
7.
Air breather hose clamp
8.
Clip E
9.
Transfer motor
10. Breather tube (transfer)
Vehicle front
ALDIA0110ZZ
ALDIA0111ZZ
AIR BREATHER HOSE
TM-193
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3. Install clip (B) on actuator/transfer motor air breather hose (1)
and transfer air breather hose (2) with the paint mark (A)
matched.
•
:Front
4. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (B) and clip (C) with the paint mark
(A) and (D) facing upward.
•
:Front
5. Install the actuator air breather hose into the actuator (case con-
nector) until the hose end reaches the base of the tube. Set
actuator air breather hose with paint mark facing leftward.
6. Install clip (B) on transfer motor air breather hose (2) and trans-
fer air breather hose (1) with the paint mark (A) matched.
•
:Front
7. Install the transfer air breather hose into the breather tube
(transfer, metal connector) until the hose end reaches the base
of the tube. Set transfer air breather hose with paint mark facing
upwards.
AWDIA0011ZZ
AWDIA0012ZZ
SDIA3226E
AWDIA0013ZZ
SDIA3196E
TM-194
< REMOVAL AND INSTALLATION >
AIR BREATHER HOSE
8. Install the transfer motor air breather hose into the transfer
motor (case connector) until the hose end reaches the end of
the curved section. Set transfer motor air breather hose with
paint mark facing leftward.
SDIA3194E
OIL PAN
TM-195
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Oil Pan
INFOID:0000000006159456
REMOVAL AND INSTALLATION
Removal
1. Drain A/T fluid. Refer to
TM-170, "Changing the A/T Fluid (ATF)"
.
2. Remove oil pan clips (1).
3. Remove oil pan (2).
4. Remove oil pan gasket.
•
Vehicle front
•
Oil pan bolts
• Drain plug (3)
5. Check for foreign materials in oil pan to help determine cause of malfunction. If the A/T fluid is very dark,
has some burned smell, or contains foreign particles then friction material (clutches, band) may need
replacement. A tacky film that will not wipe clean indicates varnish build up. Varnish can cause valves,
servo, and clutches to stick and can inhibit pump pressure.
CAUTION:
If friction material is detected, flush the transmission cooler after repair. Refer to
6. Remove magnets from oil pan.
Installation
1. Install the oil pan magnets as shown.
AWDIA0023ZZ
SCIA5200E
SCIA5200E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст