Nissan Titan A60. Instruction — part 835
FRONT SEAT
SE-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Instruction Passenger Seat
16. Outer pedestal finisher
17. Power seat frame assembly
18. Seat cushion front finisher
19. Seat cushion inner finisher
20. Seat wiring harness
21. Wire harness cover
22. Inner recliner cover
23. RH inner leg cover
24. Seat latch cover
25. Inner reclining cover
26. Outer reclining cover
27. Outboard reclining arm inner cover
28. Inboard reclining arm inner cover
29. Reclining rod
30. Armrest assembly (if equipped)
31. Armrest cap (if equipped)
32. Armrest bolt (if equipped)
33. Seatback board
AWJIA0479GB
SE-30
< REMOVAL AND INSTALLATION >
FRONT SEAT
Removal and Installation For Front Seat
INFOID:0000000006163209
REMOVAL
CAUTION:
• When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.
• Before removing the front seat, turn the ignition switch off, disconnect both battery cables and wait
at least 3 minutes.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After front side air bag module inflates, front seatback assembly must be replaced.
• Front passenger seat is equipped with Occupant Classification System sensor and control module.
Do not disassemble front passenger seat cushion assembly or remove trim as this will affect the
Occupant Classification System calibration.
• Always replace passenger seat cushion as an assembly.
1. Slide the seat until the four seat to body bolts are visible and a tool can be inserted.
NOTE:
• If disassembling the seat after removal, set the front/rear cushion lifters to the top position.
2. Disconnect both battery cables and wait at least 3 minutes.
3. Disconnect the side air bag module harness connector (if equipped).
4. Remove the bolt and leg covers.
5. Remove the four seat to body bolts.
6. Disconnect the power seat harness connectors and remove the seat from the vehicle.
NOTE:
When removing and installing the seat, use shop cloths to protect the vehicle from damage.
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation For Seat Slide/Recline Switch (Passenger Seat)
INFOID:0000000006751677
REMOVAL
1. Remove the passenger seat. Refer to
SE-30, "Removal and Installation For Front Seat"
2. Place the seat, back side down, on a work bench
1.
Headrest
2.
Headrest holder with multi position
lock
3.
Headrest holder
4.
Seat fold lever
5.
Seat fold handle and cable
6.
Seatback assembly with armrest,
with side airbag (if equipped)
7.
Seatback board without armrest,
without airbag (if equipped)
8.
Seatback frame assembly without
armrest, without airbag (if equipped)
9.
Seatback pad and cover without arm-
rest, without airbag (if equipped)
10. Seatback assembly without armrest,
with side airbag (if equipped)
11. Seat recline lever
12. Seat cushion outer finisher
13. Bolt cover
14. Outer pedestal finisher
15. Power seat frame assembly
16. Seat cushion inner finisher
17. Seat rear cover
18. Inner recliner cover
19. RH inner leg cover
20. Seat latch cover
21. Armrest cover (if equipped)
22. Inboard reclining arm inner cover
23. Outboard reclining arm outer cover
24. Outboard reclining arm outer cover
25. Seat cushion assembly
26. Armrest assembly (if equipped)
27. Armrest cap (if equipped)
28. Armrest bolt (if equipped)
29. Seatback pad and cover with arm-
rest, without airbag (if equipped)
30. Seatback frame assembly with arm-
rest, without airbag (if equipped)
31. Seatback board with armrest, without
airbag (if equipped)
FRONT SEAT
SE-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
3. Unhook the under seat flap.
4. Remove the two seat switch knobs (1) and seat switch bezel (2).
5. Remove the four bolts securing the seat pan to the seat frame.
ALJIA0573ZZ
ALJIA0574ZZ
ALJIA0575ZZ
SE-32
< REMOVAL AND INSTALLATION >
FRONT SEAT
6. Disconnect the OCS electrical connector (1) and seat switch
electrical connector (2).
7. Detach the two seat switch harness clips (1) from the seat pan.
8. Remove outboard J-clip.
ALJIA0576ZZ
ALJIA0576ZZ
ALJIA0578ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст