Nissan Titan A60. Instruction — part 955
TM-208
< UNIT REMOVAL AND INSTALLATION >
TRANSMISSION ASSEMBLY
• After inserting a torque converter to a transmission, be sure to
check distance A to ensure it is within specifications.
INSTALLATION
Installation is in the reverse order of removal, while paying attention to the following:
• When installing transmission to the engine, attach the bolts in the
order as shown.
CAUTION:
• When replacing an engine or transmission you must make
sure the dowels are installed correctly during re-assembly.
• Improper alignment caused by missing dowels may cause
vibration, oil leaks or breakage of drivetrain components.
NOTE:
*: No.2 bolt also secures air breather tube.
• Align the positions of bolts for drive plate with those of the torque
converter, and temporarily tighten the bolts. Then tighten the bolts
with the specified torque. Refer to
TM-206, "Removal and Installa-
CAUTION:
• When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
• After converter is installed to drive plate, rotate crankshaft
several turns and check to be sure that transmission rotates
freely without binding.
• Install crankshaft position sensor (POS).
• After completing installation check fluid leakage, fluid level and the
positions of A/T. Refer to
TM-168, "Checking the A/T Fluid (ATF)"
TM-184, "Checking of A/T Position"
TM-184, "Adjustment of A/T Position"
Removal and Installation (4WD)
INFOID:0000000006736260
COMPONENTS
Distance A
: 24.0 mm (0.94 in) or more
SAT017B
Transmission to engine bolts : 113 N·m (12 kg-m,
83 ft-lb)
LCIA0371E
LCIA0335E
TRANSMISSION ASSEMBLY
TM-209
< UNIT REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL
CAUTION:
When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS) from
the A/T assembly.
Be careful not to damage sensor edge.
1. Disconnect the battery negative terminal. Refer to
PG-76, "Removal and Installation"
2. Remove A/T fluid indicator.
3. Remove engine under cover using power tool.
4. Remove transfer under cover using power tool, if equipped.
5. Remove crankshaft position sensor (POS) from A/T assembly.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings or foreign material to get on the
sensor front edge magnetic area.
• Do not place in an area affected by magnetism.
6. Remove A/T fluid indicator pipe.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
7. Remove exhaust front tube and center muffler using power tool.
EX-5, "Removal and Installation"
8. Remove propeller shafts. Refer to
DLN-141, "Removal and Installation"
1.
A/T fluid indicator pipe
2.
A/T fluid indicator
3.
O-ring
4.
Transmission assembly
5.
Fluid cooler tube
6.
Copper washer
7.
A/T cross member
8.
Insulator
AWDIA0548GB
LCIA0334E
TM-210
< UNIT REMOVAL AND INSTALLATION >
TRANSMISSION ASSEMBLY
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
9. Disconnect control cable.
10. Remove A/T fluid cooler tubes from A/T assembly.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
11. Support A/T assembly using transmission jack and Tool.
CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug.
12. Remove cross member using power tool.
13. Tilt the transmission slightly to keep the clearance between body and transmission, then disconnect air
breather hose. Refer to
TM-192, "4WD : 4WD: Removal and Installation"
.
14. Remove dust cover from converter housing.
15. Turn crankshaft to access and remove the four bolts for drive
plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
16. Remove air breather hose. Refer to
TM-192, "4WD : 4WD: Removal and Installation"
17. Disconnect A/T assembly harness connector and terminal cord assembly.
18. Remove A/T assembly to engine bolts using power tool.
19. Remove A/T assembly with transfer from vehicle.
CAUTION:
• Secure torque converter to prevent it from dropping.
• Secure A/T assembly to transmission jack.
20. Remove transfer from A/T assembly. Refer to
INSPECTION
Installation and Inspection of Torque Converter
• After inserting a torque converter to a transmission, be sure to
check distance A to ensure it is within specifications.
INSTALLATION
Tool number
:
—
(J-47002)
LCIA0335E
SCIA2203E
Distance A
: 24.0 mm (0.94 in) or more
SAT017B
TRANSMISSION ASSEMBLY
TM-211
< UNIT REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Installation is in the reverse order of removal, while paying attention to the following:
• When installing transmission to the engine, attach the bolts as
shown.
CAUTION:
• When replacing an engine or transmission you must make
sure the dowels are installed correctly during re-assembly.
• Improper alignment caused by missing dowels may cause
vibration, oil leaks or breakage of drivetrain components.
NOTE:
*: No.2 bolt also secures air breather tube.
• Align the positions of bolts for drive plate with those of the torque
converter, and temporarily tighten the bolts. Then tighten the bolts
with the specified torque. Refer to
TM-208, "Removal and Installa-
CAUTION:
• When turning crankshaft, turn it clockwise as viewed from the
front of the engine.
• After converter is installed to drive plate, rotate crankshaft
several turns and check to be sure that transmission rotates
freely without binding.
• Install crankshaft position sensor (POS).
• After completing installation, check fluid leakage, fluid level, and
the positions of A/T. Refer to
TM-168, "Checking the A/T Fluid (ATF)"
TM-184, "Checking of A/T Position"
TM-184, "Adjustment of A/T Position"
.
Transmission to engine bolts : 113 N·m (12 kg-m,
83 ft-lb)
LCIA0371E
LCIA0335E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст