Nissan Titan A60. Instruction — part 181
BRC-102
< SYMPTOM DIAGNOSIS >
[VDC/TCS/ABS]
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis Procedure
INFOID:0000000006165954
1.
CHECK START
Check front and rear brake force distribution using a brake tester.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check brake system.
2.
CHECK FRONT AND REAR AXLE
Make sure that there is no excessive play in the front and rear axles. Refer to front:
RAX-5, "On-Vehicle Inspection"
.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace malfunctioning components.
3.
CHECK WHEEL SENSOR AND SENSOR ROTOR
Check the following.
• Wheel sensor installation for damage.
• Sensor rotor installation for damage.
• Wheel sensor connector connection.
• Wheel sensor harness inspection.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> • Replace wheel sensor or sensor rotor. Refer to
BRC-113, "Removal and Installation"
115, "Removal and Installation"
• Repair harness.
4.
CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp is turned off after the ignition switch is turned ON or when driving.
Is the ABS warning lamp illuminated?
YES
>> Perform self-diagnosis. Refer to
BRC-24, "CONSULT-III Function (ABS)"
.
NO
>> Inspection End.
UNEXPECTED PEDAL REACTION
BRC-103
< SYMPTOM DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
UNEXPECTED PEDAL REACTION
Diagnosis Procedure
INFOID:0000000006165955
1.
CHECK BRAKE PEDAL STROKE
Check brake pedal stroke. Refer to
BR-13, "Inspection and Adjustment - Standard Pedal"
tion and Adjustment - Adjustable Pedal"
.
Is the stroke too large?
YES
>> • Bleed air from brake tube and hose. Refer to
BR-16, "Bleeding Brake System"
• Check brake pedal, brake booster, and master cylinder for mount play, looseness, brake system
fluid leakage, etc. Refer to
BR-13, "Inspection and Adjustment - Standard Pedal"
or
"Inspection and Adjustment - Adjustable Pedal"
(master cylinder),
(brake booster).
NO
>> GO TO 2
2.
CHECK FUNCTION
Disconnect ABS actuator and electric unit (control unit) connector to deactivate ABS. Check if braking force is
normal in this condition. Connect connector after inspection.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Check brake system.
BRC-104
< SYMPTOM DIAGNOSIS >
[VDC/TCS/ABS]
THE BRAKING DISTANCE IS LONG
THE BRAKING DISTANCE IS LONG
Diagnosis Procedure
INFOID:0000000006165956
CAUTION:
The stopping distance on slippery road surfaces might be longer with the ABS operating than when
the ABS is not operating.
1.
CHECK FUNCTION
Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector to deactivate
ABS. In this condition, check stopping distance. After inspection, connect connector.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Check brake system.
ABS FUNCTION DOES NOT OPERATE
BRC-105
< SYMPTOM DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ABS FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000006165957
CAUTION:
ABS does not operate when speed is 10 km/h (6 MPH) or lower.
1.
CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp turns OFF after ignition switch is turned ON or when driving.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Perform self-diagnosis. Refer to
BRC-24, "CONSULT-III Function (ABS)"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст