Nissan Titan A60. Instruction — part 566
REAR WINDOW GLASS AND MOLDING
GW-17
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
6. Install the sealing screen.
7. Install the headliner. Refer to
INT-21, "Removal and Installation"
8. Install the rear panel. Refer to
INT-14, "Removal and Installation"
.
9. Install the rear seat. Refer to
SE-36, "Removal and Installation"
.
SETTING AFTER INSTALLATION
Setting of Limit Switch
If any of the following operations are performed the limit switch must be reset.
• Motor operation when not installed in the vehicle.
• Removal and installation of the regulator.
• Removal and installation of the motor from the regulator.
• Removal and installation of the glass.
• Removal and installation of the glass run.
Resetting
After installing each component, perform the following procedure to reset the limit switch.
1. Raise the glass to the top.
2. While pressing and holding the reset switch, lower the glass to
the bottom.
3. Release the reset switch. Verify that the reset switch returns to
the original position, if not pull the switch using suitable tool.
4. Raise the glass to the top position
CAUTION:
Do not operate the glass automatically to raise the glass to
the top position.
REPAIRING WATER LEAKS FOR REAR WINDOW GLASS
Leaks can be repaired without removing or reinstalling glass.
If water is leaking between butyl adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the rear window area while pushing glass outward.
To stop leak, apply primer (if necessary) and then butyl adhesive to the leak point.
Rear window glass bolts
6.0 N·m (0.61 Kg-m, 53 in-lb)
LIIA1826E
SIIA0347E
GW-18
< UNIT REMOVAL AND INSTALLATION >
FRONT DOOR GLASS AND REGULATOR
FRONT DOOR GLASS AND REGULATOR
Removal and Installation
INFOID:0000000006158484
FRONT DOOR GLASS
Removal
1. Remove the front door finisher panel. Refer to
INT-10, "Removal and Installation"
.
2. Position aside the vapor barrier.
3. Remove the hole cover over rear glass bolt.
4. Operate the power window main switch to raise/lower the door window until the glass bolts can be seen.
5. Remove the inside seal.
6. Remove the glass bolts.
7. While holding the front door glass, raise it at the rear end and
pull the glass out of the sash toward the outside of the door.
Installation
Installation is in the reverse order of removal.
1.
Door glass run
2.
Door glass
3.
Front door glass regulator assembly
WIIA0941E
LIIA1687E
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
FRONT DOOR GLASS AND REGULATOR
GW-19
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Fitting Inspection
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts, and glass and guide rail bolts to correct the glass position.
FRONT DOOR GLASS REGULATOR ASSEMBLY
Removal
1. Remove the front door finisher. Refer to
INT-10, "Removal and Installation"
2. Position aside the vapor barrier.
3. Remove the hole cover over rear glass bolt.
4. Operate the power window main switch to raise/lower the door window until the glass bolts can be seen.
5. Remove the inside seal.
6. Remove the glass bolts.
7. Raise the front door glass and hold it in place with suitable tool.
8. Disconnect the harness connector from the regulator assembly.
9. Remove the bolts and the regulator assembly.
Disassembly And Assembly
Remove the regulator motor from the regulator assembly.
Inspection After Removal
Check the regulator assembly for the following items. If a malfunc-
tion is detected, replace or grease it.
• Wire wear
• Regulator deformation
• Grease condition for each sliding part
The arrows in the figure show the application points of the body
grease.
Installation
If any of the following work has been done, reset the power window motor limit switch.
• Removal and installation of the regulator assembly.
• Removal and installation of the power window motor from the regulator.
• Installation of a new glass window.
• Installation of a new glass run.
WINDOW REGULATOR RESET PROCEDURE
1. Connect the door harness connector to the power window motor, and rotate the motor more than 5 turns
in the glass raising (up) direction.
2. Install the power window motor onto the regulator.
3. Install the regulator assembly into the door and secure regulator assembly with the nuts and bolt.
4. Install the glass into the door and align with the regulator, then install the glass bolts.
5. Raise the glass to the top position.
CAUTION:
LIIA0670E
Power Window Motor Up Direction
• LH motor rotate counterclockwise
• RH motor rotate clockwise
Regulator assembly nuts
and bolt
: 7.5 N·m (0.77 kg-m, 66 in-lb)
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
GW-20
< UNIT REMOVAL AND INSTALLATION >
FRONT DOOR GLASS AND REGULATOR
Do not operate the glass automatically to raise the glass to the top.
6. Reposition the vapor barrier.
7. Install the front door finisher panel. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст