Nissan Titan A60. Instruction — part 184
BRC-114
< UNIT REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
WHEEL SENSORS
• Apply a coat of suitable grease to the wheel sensor O-ring and hole.
SENSOR ROTOR
BRC-115
< UNIT REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SENSOR ROTOR
Removal and Installation
INFOID:0000000006165968
FRONT WHEEL SENSOR ROTOR
Removal and Installation
The front wheel sensor rotor is built into the front wheel hub and bearing assembly and is not removable. If
damaged, replace the front wheel hub and bearing assembly. Refer to
FAX-6, "Removal and Installation"
REAR WHEEL SENSOR ROTOR
Removal
Remove the rear axle shaft assembly. Refer to
RAX-8, "Removal and Installation"
NOTE:
It is necessary to disassemble the rear axle shaft assembly to replace the rear wheel sensor rotor.
Installation
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse the old rear wheel sensor rotor.
• Do not reuse the rear axle oil seal. The rear axle oil seal must be replaced every time the rear axle
shaft assembly is removed from the rear axle shaft housing.
BRC-116
< UNIT REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
Removal and Installation
INFOID:0000000006165969
REMOVAL
1. Disconnect the negative battery terminal.
2. Partially drain brake fluid. Refer to
3. Disconnect the actuator harness connector from the ABS actuator and electric unit (control unit).
CAUTION:
• To remove the brake tubes, use a flare nut wrench to prevent the flare nuts and brake tubes from
being damaged.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
4. Disconnect the brake tubes.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
5. Remove the three bolts and remove the ABS actuator and electric unit (control unit).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• To install, use a flare nut crowfoot and torque wrench (commercial service tools).
1.
To rear left caliper
13 N·m (1.3 kg-m, 10 ft-lb)
2.
To rear right caliper
13 N·m (1.3 kg-m, 10 ft-lb)
3.
To front left caliper
13 N·m (1.3 kg-m, 10 ft-lb)
4.
To front right caliper
13 N·m (1.3 kg-m, 10 ft-lb)
5.
From the master cylinder secondary side
18.2 N·m (1.9 kg-m, 13 ft-lb)
6.
From the master cylinder primary side
18.2 N·m (1.9 kg-m, 13 ft-lb)
7.
ABS actuator and electric unit
(control unit)
8.
Actuator harness connector
Front
WFIA0375E
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
BRC-117
< UNIT REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• Always tighten brake tubes to specification when installing.
• Never reuse drained brake fluid.
• After installation of the ABS actuator and electric unit (control unit), perform the following.
- Refill brake system with new brake fluid. Then bleed the air from the system. Refer to
.
- Adjust the steering angle sensor. Refer to
BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR
NEUTRAL POSITION : Special Repair Requirement"
- Calibrate the decel G sensor. Refer to
BRC-9, "CALIBRATION OF DECEL G SENSOR : Special Repair
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст