Nissan Titan A60. Instruction — part 802
PWC-112
< SYMPTOM DIAGNOSIS >
REAR POWER DROP GLASS DOES NOT OPERATE
REAR POWER DROP GLASS DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000006161129
1.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit.
.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK REAR POWER DROP GLASS SWITCH
Check rear power drop glass switch.
PWC-59, "Rear Power Drop Glass Circuit Inspection"
.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK REAR POWER DROP GLASS MOTOR CIRCUIT
Check rear power drop glass motor circuit.
PWC-59, "Rear Power Drop Glass Circuit Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK REAR POWER DROP GLASS RELAYS
Check rear power drop glass relays.
Refer to
PWC-60, "Rear Power Drop Glass Down Relay Check"
PWC-62, "Rear Power Drop Glass Up
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
PRECAUTIONS
PWC-113
< PRECAUTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006161130
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Work
INFOID:0000000006698796
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components.
- Water soluble dirt: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the dirty
area.
Then rub with a soft and dry cloth.
- Oily dirt: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the dirty area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
PWC-114
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000006698795
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
( J-46534 )
Trim tool set
For removing trim
AWJIA0483ZZ
POWER WINDOW MAIN SWITCH
PWC-115
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
REMOVAL AND INSTALLATION
POWER WINDOW MAIN SWITCH
Removal and Installation
INFOID:0000000006161131
REMOVAL
1. Remove the main power window and door lock/unlock switch
finisher (2) from the front door finisher LH. Refer to
2. Remove the screws from the main power window and door lock/
unlock switch (1) using suitable tool (A). Then release the main
power window door lock/unlock switch (1) from the finisher (2).
INSTALLATION
Installation is in the reverse order of removal.
ALKIA0856ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст