Nissan Titan A60. Instruction — part 975
PRECAUTIONS
VTL-3
< PRECAUTION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
Precaution for Procedure without Cowl Top Cover
INFOID:0000000006161787
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precaution for Work
INFOID:0000000006708609
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components.
- Water soluble dirt: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the dirty
area.
Then rub with a soft and dry cloth.
- Oily dirt: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the dirty area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
PIIB3706J
VTL-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000006708612
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000006161788
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
IN-CABIN MICROFILTER
VTL-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
SYSTEM DESCRIPTION
IN-CABIN MICROFILTER
Description
INFOID:0000000006161789
FUNCTION
The air inside the passenger compartment is filtered by the in-cabin
microfilters when the heater or A/C controls are set on either the
recirculation or fresh mode. The two in-cabin microfilters are located
in the heater and cooling unit assembly.
REPLACEMENT TIMING
Replacement of the two in-cabin microfilters is recommended on a regular interval depending on the driving
conditions. Refer to For
MA-9, "FOR NORTH AMERICA : Introduction of Periodic Maintenance"
(United States
and Canada) or
MA-13, "FOR MEXICO : Introduction of Periodic Maintenance"
(Mexico). It may also be nec-
essary to replace the two in-cabin microfilters as part of a component replacement if the in-cabin microfilters
are damaged.
LJIA0012E
VTL-6
< PERIODIC MAINTENANCE >
IN-CABIN MICROFILTER
PERIODIC MAINTENANCE
IN-CABIN MICROFILTER
Removal and Installation
INFOID:0000000006161790
REPLACEMENT PROCEDURE
1. Remove the two lower glove box hinge pins to remove the glove
box from the instrument panel and let it hang from the cord.
2. Remove the screw and remove the in-cabin microfilter cover.
3. Remove the in-cabin microfilters from the heater and cooling
unit assembly housing.
4. Insert the first new in-cabin microfilter into the heater and cool-
ing unit assembly housing and slide it over to the right. Insert the
second new in-cabin microfilter into the heater and cooling unit
assembly housing.
NOTE:
The in-cabin microfilters are marked with air flow arrows. The
end of the microfilter with the arrow should face the rear of the
vehicle. The arrows should point downward.
5. Install the in-cabin microfilter cover.
WLIA0027E
LJIA0134E
LJIA0148E
LJIA0134E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст