Nissan Titan A60. Instruction — part 521
HEADLAMP
EXL-139
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Installation
Installation is in the reverse order of removal.
HEADLAMP (INNER SIDE), FOR HIGH BEAM
Removal
1. Remove the combination lamp assembly. Refer to
EXL-139, "Removal and Installation"
.
2. Turn the bulb socket counterclockwise and remove bulb.
Installation
Installation is in the reverse order of removal.
TURN SIGNAL/PARKING LAMP (FRONT)
Removal
1. Remove the combination lamp assembly. Refer to
EXL-139, "Removal and Installation"
.
2. Turn the bulb socket counterclockwise to unlock.
3. Pull the bulb to remove from the socket.
Installation
Installation is in the reverse order of removal.
SIDE MARKER LAMP (FRONT)
Removal
1. Remove the combination lamp assembly. Refer to
EXL-139, "Removal and Installation"
.
2. Turn the side marker lamp (front) bulb socket counterclockwise and remove side marker lamp (front) bulb
socket.
3. Pull to remove side marker lamp (front) from the side marker lamp (front) bulb socket.
Installation
Installation is in the reverse order of removal.
Removal and Installation
INFOID:0000000006179079
COMBINATION LAMP ASSEMBLY (FRONT)
WARNING:
• Do not touch bulb by hand right after being turned off. Burning may result.
CAUTION:
• Turn headlamp switch OFF before disconnecting headlamp harness connector.
• Do not touch the glass of bulb directly by hand. Keep grease and other oily substances away from it.
• Do not leave bulb out of combination lamp assembly (front) for a long time because dust, moisture,
smoke, etc. may affect the performance of the lamp. When replacing bulb, be sure to replace it with a
new one.
Removal
1. Remove the front grille. Refer to
EXT-19, "Removal and Installation"
2. Remove the bolts (A), disconnect the electrical connectors, and
remove the front combination lamp assembly (1).
Installation
Installation is in the reverse order of removal.
ALLIA0330ZZ
EXL-140
< REMOVAL AND INSTALLATION >
HEADLAMP
Disassembly and Assembly
INFOID:0000000006179080
FRONT COMBINATION LAMP ASSEMBLY
Disassembly
1. Turn high beam bulb counterclockwise to unlock and remove high beam bulb.
2. Turn low beam bulb counterclockwise to unlock and remove low beam bulb.
3. Turn turn signal/parking lamp (front) bulb socket counterclockwise to unlock and remove turn signal/park-
ing lamp (front) bulb.
4. Turn side marker lamp (front) bulb socket counterclockwise to unlock and remove side marker lamp (front)
bulb.
Assembly
Assembly is in the reverse order of disassembly.
1. Headlamp bulb (high beam)
2. Wiring harness assembly (inner)
3. Combination lamp assembly
4. Side marker lamp (front) bulb
5. Turn signal/parking lamp (front) bulb
6. Headlamp bulb (low beam)
AWKIA1324ZZ
AUTO LIGHT SYSTEM
EXL-141
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
AUTO LIGHT SYSTEM
Removal and Installation
INFOID:0000000006179081
OPTICAL SENSOR
Removal
1. Remove defroster grille. Refer to
2. Disconnect the optical sensor connector.
3. Turn the optical sensor counterclockwise to remove it from
defroster grille.
Installation
Installation is in the reverse order of removal.
WKIA1061E
EXL-142
< REMOVAL AND INSTALLATION >
FRONT FOG LAMP
FRONT FOG LAMP
Aiming Adjustment
INFOID:0000000006179082
The fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb. Before performing aiming
adjustment, make sure of the following.
• Keep all tires inflated to correct pressure.
• Place vehicle on level ground.
• See that vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and
tools). Have the driver or equivalent weight placed in driver seat.
Adjust aiming in the vertical direction by turning the adjustment
screw.
NOTE:
Access adjustment screw from underneath front bumper. Use a T-3
(3 mm) Torx® bit or a 3 mm allen wrench to adjust. Turn screw clock-
wise to raise pattern and counterclockwise to lower pattern.
1. Set the distance between the screen and the center of the fog
lamp lens as shown.
2. Turn front fog lamps ON.
3. Adjust front fog lamps using adjusting screw so that the top edge
of the high intensity zone is 100 mm (4 in) below the height of
the fog lamp centers as shown.
• When performing adjustment, if necessary, cover the head-
lamps and opposite fog lamp.
WKIA1396E
MEL327G
MEL328G
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст