Nissan Titan A60. Instruction — part 994
INSPECTION AND ADJUSTMENT
WT-5
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
INSPECTION AND ADJUSTMENT
Preliminary Check
INFOID:0000000006179277
1.
TIRE PRESSURE
Check all tire pressures. Refer to
Do tire pressures match specification?
YES
>> GO TO 2.
NO
>> Adjust tire pressures to specified value.
2.
LOW TIRE PRESSURE WARNING LAMP
Check low tire pressure warning lamp activation.
Does the low tire pressure warning lamp activate for one second when ignition switch is turned ON?
YES
>> GO TO 3.
NO
WT-36, "Low Tire Pressure Warning Lamp Does Not Come On When Ignition Switch Is
.
3.
BCM CONNECTOR
1. Disconnect BCM harness connectors.
2. Check terminals for damage or loose connections.
3. Reconnect harness connectors.
Are BCM connectors damaged or loose?
YES
>> Repair or replace damaged parts.
NO
>> GO TO 4.
4.
TRANSMITTER ACTIVATION TOOL
Check battery in transmitter activation tool.
Is transmitter activation tool battery fully charged?
YES
>> Perform self-diagnosis. Refer to
WT-11, "CONSULT-III Function (BCM - AIR PRESSURE MONI-
NO
>> Replace battery in transmitter activation tool.
Transmitter Wake Up Operation
INFOID:0000000006179278
NOTE:
This procedure must be done after replacement of a low tire pressure warning transmitter or BCM.
New replacement transmitters are provided "asleep" and must first be "woken up" using Transmitter
Activation Tool J-45295 before ID registration can be performed.
1. Turn ignition switch ON. Push the transmitter activation tool
against the tire near the front left transmitter. Press the button for
5 seconds. The hazard warning lamps flash per the following
diagram.
2. Repeat this procedure for each tire in the following order: FL, FR, RR, RL.
Tool number
: (J-45295)
LEIA0036E
WT-6
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
3. When the BCM finishes assigning each tire ID, the BCM flashes the hazard warning lamps and sends
flashing indicator status by CAN according to the following time chart.
4. After completing wake up of all transmitters, make sure low tire pressure warning lamp goes out.
ID Registration Procedure
INFOID:0000000006179279
ID REGISTRATION WITH TRANSMITTER ACTIVATION TOOL
NOTE:
This procedure must be done after replacement of a low tire pressure warning transmitter or BCM.
New replacement transmitters are provided "asleep" and must first be "woken up" using Transmitter
Activation Tool J-45295 before ID registration can be performed.
1. Connect CONSULT-III.
2. Select "ID REGIST" under BCM.
3. Push the transmitter activation tool against the tire near the front
left transmitter. Press the button for 5 seconds.
4. Register the IDs in order from FR LH, FR RH, RR RH and RR LH. When ID registration of each wheel has
been completed, the hazard warning lamps flash.
5. After completing all ID registrations, press “END” to complete the procedure.
NOTE:
Be sure to register all of the IDs in order from FR LH, FR RH, RR RH, to RR LH, or the self-diagnostic results
display will not function properly.
ID REGISTRATION WITHOUT TRANSMITTER ACTIVATION TOOL
NOTE:
WEIA0177E
Tool number
: (J-45295)
LEIA0036E
Step
Activation tire position
Hazard warning lamp
CONSULT-III
1
Front LH
2 times flashing
“YET”
↓
“DONE”
2
Front RH
3
Rear RH
4
Rear LH
INSPECTION AND ADJUSTMENT
WT-7
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
This procedure must be done after replacement of a low tire pressure warning transmitter or BCM.
New replacement transmitters are provided "asleep" and must first be "woken up" using Transmitter
Activation Tool J-45295 before ID registration can be performed.
1. Connect CONSULT-III.
2. Select "ID REGIST" under BCM.
3. Adjust the tire pressures to the values shown in the table and drive the vehicle at 40 km/h (25 MPH) or
more for a few minutes.
4. After completing all ID registrations, press “END” to complete the procedure.
5. Inflate all tires to proper pressure. Refer to
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
250 (2.5, 36)
Front RH
230 (2.3, 33)
Rear RH
210 (2.1, 30)
Rear LH
190 (1.9, 27)
Activation tire position
CONSULT-III
Front LH
“YET”
↓
“DONE”
Front RH
Rear RH
Rear LH
WT-8
< SYSTEM DESCRIPTION >
TPMS
SYSTEM DESCRIPTION
TPMS
System Diagram
INFOID:0000000006179280
System Description
INFOID:0000000006179281
DESCRIPTION
During driving, the tire pressure monitoring system receives the signal transmitted from the transmitter
installed in each wheel, and turns on the low tire pressure warning lamp when the tire pressure becomes low.
The control unit (BCM) for this system has pressure judgement and self-diagnosis functions.
FUNCTION
When the tire pressure monitoring system detects low inflation pressure or an internal malfunction, the low tire
pressure warning lamp in the combination meter comes on. The malfunction is indicated by the low tire pres-
sure warning lamp flashing.
BODY CONTROL MODULE (BCM)
The BCM is shown with the lower instrument panel LH removed. The
BCM reads the air pressure signal received by the remote keyless
entry receiver, and controls the low tire pressure warning lamp as
shown below. It also has a self-diagnosis function to detect a system
malfunction.
TRANSMITTER
ALEIA0004GB
Condition
Low tire pressure warning lamp
System normal
On for 1 second after ignition ON
Tire less than 193 kPa (2.0 kg/cm
2
, 28 psi)
[Flat tire]
ON
TPMS malfunction
After key ON, flashes once per sec-
ond for 1 minute, then stays ON
LEIA0068E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст