Nissan Titan A60. Instruction — part 668
BODY SIDE TRIM
INT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finisher.
LOWER DASH SIDE FINISHER
Removal
1. Remove the push pin from lower dash side finisher.
2. Remove the front kicking plate.
3. Remove the lower dash side finisher and front kicking plate together.
4. Remove the lower dash side finisher from front kicking plate.
Installation
Installation is in the reverse order of removal.
1.
Center pillar upper finisher
2.
Center pillar assist grip
3.
Rear door welt
4.
Rear door parting seal
5.
Rear kicking plate
6.
Center pillar lower finisher
7.
Front kicking plate
8.
Plastic clip C103
9.
Lower dash side finisher
10. Front door parting seal
11. Front door welt
12. Front pillar assist grip
13. Front pillar finisher
Pawl
WIIA1002E
INT-16
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
CENTER PILLAR LOWER FINISHER
Removal
1. Remove the seat belt lower anchor. Refer to
SB-13, "Removal and Installation"
• On RH side, disconnect seat belt tension sensor.
2. Remove the front and rear kicking plates.
3. Remove the center pillar lower finisher.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR UPPER FINISHER
Removal
1. Remove the front and rear door welts.
2. Remove the front and rear kicking plates.
3. Remove the center pillar lower finisher.
4. Remove the seat belt shoulder anchor and D ring. Refer to
SB-4, "Removal and Installation of Front Seat
5. Remove the center pillar assist grip.
6. Remove the center pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR FINISHER
Removal
1. Remove the front pillar assist grip.
2. Remove the front pillar finisher.
Installation
Installation is in the reverse order of removal.
KICKING PLATES
Removal
Release the clips and remove the front and/or rear kicking plates.
Installation
Installation is in the reverse order of removal.
DOOR PARTING SEALS
Removal
1. Open the front and/or rear doors fully.
2. Release the clips and remove the parting seals.
Installation
Installation is in the reverse order of removal.
REAR
BODY SIDE TRIM
INT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
1.
Drafter duct (Crew Cab)
2.
Drafter duct cover (Crew Cab)
3.
Rear upper finisher RH
4.
Rear panel (Crew Cab)
5.
Rear lower finisher RH
6.
Push pin
7.
Nut
8.
Center anchor bracket cover
9.
Drafter duct cover (King Cab)
10. Drafter duct (King Cab)
11. Rear lower finisher LH
12. Plastic clip C101
13. Metal clip
14. Rear panel (King Cab)
15. Rear upper finisher LH
16. Rear panel upper finisher
WIIA1003E
INT-18
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from finishers.
Removal
1. Remove rear seats. Refer to
SE-36, "Removal and Installation"
2. Remove rear kicking plates.
3. Remove seat belt anchor bolts. Refer to
SB-13, "Removal and Installation"
4. Remove seatback latch strikers. Refer to
SE-36, "Removal and Installation"
.
5. Remove rear lower finishers LH/RH.
6. Remove rear upper finishers LH/RH.
7. Remove center anchor bracket cover, if equipped.
8. Remove rear panel upper finisher and rear panel.
9. Remover drafter duct cover and drafter duct.
Installation
Installation is in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст