Nissan Titan A60. Instruction — part 894
STEERING COLUMN
ST-13
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Floor Shift Model
CAUTION:
• Any time the ignition switch has been disconnected, removed or installed, the keys must be re-regis-
tered in the BCM. Refer to Consult-III operations IVIS/NVIS.
• Care must be taken not to give axial impact to steering column assembly during removal and instal-
lation.
• Care must be taken not to move steering gear during removal of steering column assembly.
REMOVAL
1. Remove spiral cable from steering column assembly with combination switches attached. Refer to
2. Remove tilt lever knob from tilt lever by inserting a suitable tool
into slot of tilt lever knob, then depress tab and withdraw tilt lever
knob.
AWGIA0117GB
1.
Driver air bag module
2.
Steering wheel
3.
Steering wheel side cover
4.
Combination switch and spiral cable 5.
Steering column assembly
6.
Collar
7.
Hole cover seal
8.
Clamp
9.
Hole cover mounting plate
10. Hole cover
11. Upper joint
12. Upper shaft
13. Boot clamp
14. Lower joint shaft
15. Boot and clips (plastic)
WGIA0061E
ST-14
< UNIT REMOVAL AND INSTALLATION >
STEERING COLUMN
3. Remove lower driver instrument panel. Refer to
IP-17, "Removal and Installation"
.
4. Remove steering column cover and ignition key finisher. Refer to
IP-12, "Removal and Installation"
.
5. Remove knee protector screws, then remove knee protector
from vehicle.
6. Disconnect the following:
• Sonar switch
• Adjustable pedal switch
• Wiper switch
• Headlamp switch
• Immobilizer
• Ignition switch
• Spiral cable
7. On models equipped with column shift, disconnect shift cable from steering column. Refer to
T Shift Selector Removal and Installation"
8. Remove lock nut and bolt, then separate lower joint from upper
joint.
9. Remove steering member nuts, then remove steering column
assembly from steering member.
10. Remove hole cover seal and clamp.
11. Remove nuts, then remove hole cover from the lower dash.
LGIA0026E
LGIA0027E
LGIA0028E
STEERING COLUMN
ST-15
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
12. Remove bolt (lower side) of lower joint and remove lower joint
from vehicle.
INSPECTION AFTER REMOVAL
• Check for damage to steering column jacket tube. If damage is found, replace steering column with new
one.
• If the vehicle has been involved in a collision, or if noise and rattles
are heard during a turn, check the length (L, L
1
and L
2
) of the col-
umn. If out of specification, replace the steering column as an
assembly.
• Check for proper lubrication, apply grease as necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When installing the steering column, finger-tighten all of the lower bracket and joint retaining bolts;
then tighten them to specification. Do not apply undue stress to the steering column.
NOTE:
Align slit of the coupling joint with projection on dust cover. Insert the
joint until surface (A) contacts surface (B).
• After installation, turn steering wheel to make sure it moves
smoothly. Make sure the number of turns are the same from the
straight-forward position to left and right locks. Make sure that the
steering wheel is in a neutral position when driving straight ahead.
• When installing steering column to steering member, install nut
from front side of vehicle.
INSPECTION AFTER INSTALLATION
• After installing the steering column, check the tilt mechanism for proper operation.
LGIA0029E
Steering column length
L
: Refer to
L
1
: Refer to
L
2
: Refer to
SGIA0475E
WGIA0080E
SST491C
ST-16
< UNIT REMOVAL AND INSTALLATION >
STEERING COLUMN
• Check if steering wheel operation can turn to the end of the left and right stops smoothly.
Range (A)
:Refer to
WGIA0083E
WGIA0026E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст