Nissan Titan A60. Instruction — part 746
PB-4
< PERIODIC MAINTENANCE >
PARKING BRAKE SYSTEM
PERIODIC MAINTENANCE
PARKING BRAKE SYSTEM
On-Vehicle Service
INFOID:0000000006158510
PEDAL STROKE
• When parking brake pedal is operated with the specified force, make sure the stroke is within the specified
number of notches. Check by listening and counting the ratchet clicks.
INSPECTION
• Make sure the components are attached properly, checking for looseness or backlash.
• Check parking brake pedal assembly for bends, damage and cracks, and replace if necessary.
• Check cable for wear and damage, and replace if necessary.
• Check parking brake warning lamp switch for malfunction, and replace if necessary. Refer to
.
ADJUSTMENT
1. Remove the lower instrument panel LH. Refer to
IP-17, "Removal and Installation"
.
2. Partially engage parking brake pedal to access adjusting nut.
3. Insert a deep socket wrench to rotate adjusting nut and loosen
cable sufficiently. Then, disengage the parking brake pedal.
4. Remove the wheel and tire using power tool.
5. Remove the disc rotor and measure inner diameter at widest
point using suitable tool.
6. Transfer measurement less 0.6 mm (0.024 in) to the parking
brake shoes and adjust accordingly.
7. Using wheel nuts, secure the disc rotor to the hub to prevent it
from tilting.
8. Rotate the disc rotor to make sure there is no drag.
9. Adjust cable as follows:
a. Operate pedal 10 or more times with a force of 196 N (20 kg-f,
44 lb-f).
b. Rotate adjusting nut with deep socket to adjust pedal stroke to
specification.
c.
With parking brake pedal completely disengaged, make sure
there is no drag on the parking brake.
10. Install the disc rotor.
11. Install the wheel and tire using power tool.
Pedal stroke
: Refer to
PB-11, "Parking Brake Control"
.
WFIA0165E
Tool number
: — (J-21177-A)
Pedal stroke
: Refer to
PB-11, "Parking Brake Control"
.
WFIA0166E
PARKING BRAKE SYSTEM
PB-5
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
12. Install the lower instrument panel LH. Refer to
PB-6
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
REMOVAL AND INSTALLATION
PARKING BRAKE CONTROL
Component
INFOID:0000000006158511
Removal and Installation
INFOID:0000000006158512
REMOVAL
1. Remove lower instrument panel LH. Refer to
IP-17, "Removal and Installation"
.
2. On models with floor shift, remove center console. Refer to
IP-23, "Disassembly and Assembly"
3. Remove floor trim. Refer to
INT-19, "Removal and Installation"
4. Remove adjusting nut and discard.
CAUTION:
Do not reuse adjusting nut after removing it.
5. Remove the lock plate from the front cable.
6. Remove front cable retaining bolts and nut.
7. Disconnect return spring from equalizer.
8. Disconnect right and left rear cables from equalizer.
9. Remove rear disc rotors. Refer to
tion of Brake Caliper and Disc Rotor"
.
1.
Pedal assembly
2.
Front cable
3.
Right rear cable
4.
Left rear cable
5.
Return spring
6.
Equalizer
7.
Adjusting nut
8.
Lock plate
WFIA0218E
WFIA0165E
PARKING BRAKE CONTROL
PB-7
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
10. Remove parking brake shoe, and remove rear cable from toggle lever. Refer to
.
11. Remove right and left rear cables retaining bolts and nuts, then remove right and left rear cables.
INSTALLATION
Installation is in the reverse order of removal.
• Adjust parking brake. Refer to
.
CAUTION:
Do not reuse adjusting nut after removing it.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст