Nissan Titan A60. Instruction — part 528
EXT-18
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Removal and Installation
INFOID:0000000006163336
REMOVAL
1. Disconnect the sonar sensor harness connector, if equipped.
• Disconnect the sonar sensors from retainers.
2. Disconnect the license lamp harness.
3. Remove the clips from the license lamps and remove lamps.
4. Release the clips and remove the upper step pads.
5. Remove the rear bumper reinforcement bolts and remove the rear bumper.
6. Disconnect the harness clips from the black steel bumper.
7. Remove the sonar sensor retainers from the rear bumper, if equipped.
8. Remove the sonar sensors and harness from the rear bumper, if equipped.
• Disconnect the sonar sensors from harness.
9. Remove the license lamp harness from the rear bumper.
INSTALLATION
Installation is in the reverse order of removal.
• Apply sealant to clips securing upper step pad during installation.
1.
Rear bumper reinforcement
2.
Sonar sensor harness (if equipped)
3.
Sonar sensor (if equipped)
4.
License lamp harness
5.
Upper step pad
6.
License lamp clip
7.
Carriage bolt
8.
Rear bumper
9.
Sonar sensor retainer (if equipped)
10. License lamp
11. License lamp washer
12. Lower step pad
AWKIA1596GB
FRONT GRILLE
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FRONT GRILLE
Removal and Installation
INFOID:0000000006163337
REMOVAL
1. Release the plastic clips and remove the front grille.
2. Remove the LH and RH front bumper filler panels.
3. Remove the front emblem, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
1.
Plastic clip CG101
2.
Plastic clip CG101
3.
Grommet
4.
Front bumper filler panel RH
5.
Front grille
6.
Front bumper filler panel LH
WIIA0986E
EXT-20
< REMOVAL AND INSTALLATION >
COWL TOP
COWL TOP
Removal and Installation
INFOID:0000000006163338
REMOVAL
1. Remove the right and left wiper arms. Refer to
.
2. Remove the cowl top seal.
• Release the plastics clips on the cowl top seal which go through the cowl tops LH and RH and cowl top
extension.
3. Remove the cowl top covers LH and RH.
• Release the plastic clips under cowl top covers attaching to grommets on hoodledge.
• Disconnect the washer tubes from washer nozzles.
4. Remove the cowl top extension brackets LH and RH.
• Disconnect the wiper motor harness from cowl top extension bracket LH.
• Cowl top extension bracket LH must be removed prior to removal of the wiper motor and connecting rod
assembly.
5. Remove the wiper motor and connecting rod linkage. Refer to
WW-54, "Wiper Motor and Linkage"
.
1.
Grommet
2.
Plastic clip C103
3.
Cowl top RH
4.
Cowl top seal
5.
Drain tube
6.
Cowl top extension bracket RH
7.
Cowl top extension
8.
Cowl top extension bracket LH
9.
Cowl top LH
WIIA0987E
COWL TOP
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
6. Disconnect the windshield washer tube. Refer to
7. Remove the A/C low-pressure pipe bracket from cowl top extension. Refer to
8. Remove the drain tube from each side of cowl top extension.
9. Remove the cowl top extension.
INSTALLATION
Installation is in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст