Nissan Titan A60. Instruction — part 838
FRONT SEAT
SE-41
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Center Seat
WIIA0947E
1.
Cupholder
2.
Armrest assembly
3.
Armrest pivot arm
4.
Armrest release bracket
5.
Armrest pivot release lever
6.
Upper armrest pivot cover
7.
Lower armrest pivot cover
8.
Seat cushion cover
9.
Seat cushion pad
10. RH pedestal support
11. LH pedestal support
12. Seat belt tongue
13. Center seat pan
14. Inboard lower pivot cover
15. Rear hinge cover
16. Inboard armrest support cover
17. Armrest support
18. Armrest bolt cover
SE-42
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Power Passenger Seat
AWJIA0478GB
1.
Headrest
2.
Headrest holder with multi position
lock
3.
Headrest holder
4.
Seat fold lever
5.
Seat fold handle and cable
6.
Seatback assembly with armrest,
with side airbag (if equipped)
7.
Power seat switch
8.
Power seat switch escutcheon
9.
Recliner switch
10. Seat slide switch
11. Seat cushion assembly
12. Outboard reclining arm outer cover
13. Seatback assembly without arm rest 14. Seat cushion outer finisher
15. Bolt cover
FRONT SEAT
SE-43
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Instruction Passenger Seat
16. Outer pedestal finisher
17. Power seat frame assembly
18. Seat cushion front finisher
19. Seat cushion inner finisher
20. Seat wiring harness
21. Wire harness cover
22. Inner recliner cover
23. RH inner leg cover
24. Seat latch cover
25. Inner reclining cover
26. Outer reclining cover
27. Outboard reclining arm inner cover
28. Inboard reclining arm inner cover
29. Reclining rod
30. Armrest assembly (if equipped)
31. Armrest cap (if equipped)
32. Armrest bolt (if equipped)
33. Seatback board
AWJIA0479GB
SE-44
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Disassembly and Assembly
INFOID:0000000006163213
SEATBACK TRIM AND PAD
NOTE:
Only complete outboard seatback assemblies can be replaced on vehicles equipped with side air bags.
Be sure to set the front/rear cushion lifter to the top position.
1. Remove the seatback board.
2. Remove the retainer.
3. Remove the headrest.
4. From inside of the seatback, squeeze the headrest holder tabs
at the base of the stay pipe and pull the up to remove.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and right/left).
1.
Headrest
2.
Headrest holder with multi position
lock
3.
Headrest holder
4.
Seat fold lever
5.
Seat fold handle and cable
6.
Seatback assembly with armrest,
with side airbag (if equipped)
7.
Seatback board without armrest,
without airbag (if equipped)
8.
Seatback frame assembly without
armrest, without airbag (if equipped)
9.
Seatback pad and cover without arm-
rest, without airbag (if equipped)
10. Seatback assembly without armrest,
with side airbag (if equipped)
11. Seat recline lever
12. Seat cushion outer finisher
13. Bolt cover
14. Outer pedestal finisher
15. Power seat frame assembly
16. Seat cushion inner finisher
17. Seat rear cover
18. Inner recliner cover
19. RH inner leg cover
20. Seat latch cover
21. Armrest cover (if equipped)
22. Inboard reclining arm inner cover
23. Outboard reclining arm outer cover
24. Outboard reclining arm outer cover
25. Seat cushion assembly
26. Armrest assembly (if equipped)
27. Armrest cap (if equipped)
28. Armrest bolt (if equipped)
29. Seatback pad and cover with arm-
rest, without airbag (if equipped)
30. Seatback frame assembly with arm-
rest, without airbag (if equipped)
31. Seatback board with armrest, without
airbag (if equipped)
SIIA0113E
LRS023
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст