Nissan Titan A60. Instruction — part 418
EC-338
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
P0550 PSP SENSOR
2.
CHECK PSP SENSOR POWER SUPPLY CIRCUIT
1. Disconnect power steering pressure (PSP) sensor (1) harness
connector.
2. Turn ignition switch ON.
3. Check voltage between PSP sensor terminal 1 and ground with
CONSULT-III or tester.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connectors.
3.
CHECK PSP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check harness continuity between PSP sensor terminal 3 and ECM terminal 67.
Refer to Wiring Diagram.
4. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK PSP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check harness continuity between ECM terminal 12 and PSP sensor terminal 2.
2. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK PSP SENSOR
EC-339, "Component Inspection"
OK or NG
OK
>> GO TO 6.
NG
>> Replace PSP sensor.
6.
CHECK INTERMITTENT INCIDENT
GI-36, "How to Check Terminal"
and
GI-39, "Intermittent Incident"
>> INSPECTION END
BBIA0741E
Voltage: Approximately 5V
PBIB0188E
Continuity should exist.
Continuity should exist.
P0550 PSP SENSOR
EC-339
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Component Inspection
INFOID:0000000006158780
POWER STEERING PRESSURE SENSOR
1. Reconnect all harness connectors disconnected.
2. Start engine and let it idle.
3. Check voltage between ECM terminal 12 and ground under the
following conditions.
Condition
Voltage
Steering wheel: Being turned
0.5 - 4.5V
Steering wheel: Not being turned
0.4 - 0.8V
MBIB0126E
EC-340
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
P0603 ECM POWER SUPPLY
P0603 ECM POWER SUPPLY
Component Description
INFOID:0000000006158781
Battery voltage is supplied to the ECM even when the ignition switch
is turned OFF for the ECM memory function of the DTC memory, the
air-fuel ratio feedback compensation value memory, the idle air vol-
ume learning value memory, etc.
On Board Diagnosis Logic
INFOID:0000000006158782
DTC Confirmation Procedure
INFOID:0000000006158783
1. If DTC Confirmation Procedure has been previously conducted, always perform the following before con-
ducting the next step.
a. Turn ignition switch OFF and wait at least 10 seconds.
b. Turn ignition switch ON.
c.
Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON wait at least 10 seconds.
3. Turn ignition switch OFF and wait at least 5 minutes.
4. Turn ignition switch ON, wait at least 10 seconds.
5. Repeat steps 2 and 3 for five times.
6. Check 1st trip DTC.
If 1st trip DTC is detected, go to
.
Diagnosis Procedure
INFOID:0000000006158784
1.
CHECK ECM POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check voltage between ECM terminal 121 and ground with
CONSULT-III or tester.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
PBIB1164E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0603
0603
ECM power supply circuit
ECM back-up RAM system does not function
properly.
• Harness or connectors
[ECM power supply (back-up) circuit is
open or shorted.]
• ECM
Voltage: Battery voltage
MBIB0026E
P0603 ECM POWER SUPPLY
EC-341
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Check the following.
• IPDM E/R connector E121
• 20A fuse
• Harness for open or short between ECM and battery
>> Repair or replace harness or connectors.
3.
CHECK INTERMITTENT INCIDENT
GI-36, "How to Check Terminal"
GI-39, "Intermittent Incident"
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness or connectors.
4.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III
1. Turn ignition switch ON.
2. Select “SELF DIAG RESULTS” mode with CONSULT-III.
3. Touch “ERASE”.
4. Perform DTC Confirmation Procedure.
EC-340, "DTC Confirmation Procedure"
5. Is the 1st trip DTC P0603 displayed again?
With GST
1. Turn ignition switch ON.
2. Select Service $04 with GST.
3. Perform DTC Confirmation Procedure.
EC-340, "DTC Confirmation Procedure"
4. Is the 1st trip DTC P0603 displayed again?
Yes or No
Yes
>> GO TO 5.
No
>> INSPECTION END
5.
REPLACE ECM
1. Replace ECM.
2. Perform initialization of NVIS(NATS) system and registration of all NVIS(NATS) ignition key IDs. Refer to
SEC-7, "ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement"
.
3. Perform
.
4. Perform
EC-119, "Accelerator Pedal Released Position Learning"
.
5. Perform
EC-119, "Throttle Valve Closed Position Learning"
6. <Flexible Fuel Vehicle>
Perform
EC-119, "Ethanol Mixture Ratio Adaptation (Flexible Fuel Vehicle)"
.
7. Perform
EC-120, "Idle Air Volume Learning"
.
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст