Nissan Titan A60. Instruction — part 149
BRAKE TUBE AND HOSE
BR-23
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
Removal and Installation of Rear Brake Piping and Brake Hose
INFOID:0000000006163286
REMOVAL
1. Drain brake fluid. Refer to
2. Using a flare nut wrench, remove brake tube from brake hose.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
3. Remove lock plate and brake hose from bracket.
4. Remove brake hose connection (A) from cylinder body.
CAUTION:
Do not reuse copper washer.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
INSTALLATION
1. Install brake hose connection (A) and new copper washer to cyl-
inder body and tighten to specification. Refer to
.
CAUTION:
Do not reuse copper washer.
2. Insert brake hose end through bracket, then secure it to bracket
with lock plate.
3. Install brake tube to brake hose, then tighten the flare nut using
a suitable tool. Refer to
4. Refill brake fluid and bleed air. Refer to
BR-16, "Bleeding Brake System"
.
LFIA0213E
ALFIA0152ZZ
ALFIA0152ZZ
LFIA0213E
BR-24
< REMOVAL AND INSTALLATION >
BRAKE TUBE AND HOSE
Inspection After Installation
INFOID:0000000006163287
CAUTION:
Brake tubes and hoses are important safety parts. Always disassemble the parts and retighten their fit-
tings, if a brake fluid leak is detected. Replace applicable part with a new one, if a damaged part is
detected.
1. Check brake lines (tubes and hoses), and connections for fluid leaks, damage, twist, deformation, contact
with other parts, and loose connections. Replace any parts as necessary. Refer to
2. While depressing brake pedal under a force of 785 N (80 kg-f, 177 lb-f) with engine running for approxi-
mately 5 seconds, check each part for fluid leaks.
BRAKE MASTER CYLINDER
BR-25
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE MASTER CYLINDER
Exploded View
INFOID:0000000006163288
With VDC/TCS/ABS
CAUTION:
Be careful not to splash brake fluid on painted areas; it way cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
Removal and Installation
INFOID:0000000006163289
REMOVAL
CAUTION:
• Be careful not to splash brake fluid on painted areas; it way cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Before removing brake master cylinder, depress the brake pedal 5-6 times with the key OFF to
deplete vacuum in the booster.
1. Remove brake reservoir cap.
2. Disconnect harness connector for fluid level sensor, front and rear pressure sensors (if equipped).
3. Using a flare nut wrench, disconnect brake tube from master cylinder assembly.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
4. Remove master cylinder assembly nuts and remove the master cylinder assembly.
AWFIA0415GB
1.
Reservoir cap
2.
Fluid level sensor
3.
Grommet
4.
Master cylinder sub-assembly
5.
Rear pressure sensor
6.
Front pressure sensor
7.
Seal
8.
Reservoir tank
B: Brake fluid
R: Rubber grease
BR-26
< REMOVAL AND INSTALLATION >
BRAKE MASTER CYLINDER
CAUTION:
Discard nuts, do not reuse.
INSTALLATION
Installation is in the reverse order of removal.
• Refill brake fluid and bleed air. Refer to
BR-16, "Bleeding Brake System"
.
CAUTION:
• Be careful not to splash brake fluid on painted areas; it way cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Refill with new brake fluid. Refer to
MA-21, "FOR NORTH AMERICA : Fluids and Lubricants"
(United States and Canada),
MA-22, "FOR MEXICO : Fluids and Lubricants"
(Mexico).
• Do not reuse drained brake fluid.
• Adjust brake pedal. Refer to
BR-13, "Inspection and Adjustment - Standard Pedal"
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст