Nissan Titan A60. Instruction — part 533
PREPARATION
FAX-3
< PREPARATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000006161620
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000006161621
Tool number
(Kent-Moore No.)
Tool name
Description
ST29020001
(J-24319-01)
Gear arm puller
Removing ball joint for steering knuckle
a: 34 mm (1.34 in)
b: 6.5 mm (0.256 in)
c: 61.5 mm (2.421 in)
KV40107300
(
—
)
Boot band crimping tool
Installing boot bands
NT694
ZZA1229D
Tool name
Description
Power tools
Removing bolts and nuts
PBIC0190E
FAX-4
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000006161622
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
—
(2
F1
31
0)
"
Re
fer
to
DRI
VE SHAF
T in
th
is cha
rt.
Re
fer
to
WHEEL
HUB in
th
is cha
rt.
"
"
Possible cause and SUSPECTED PARTS
Ex
ce
ss
iv
e j
oi
nt an
gl
e
Jo
in
t s
lid
in
g re
si
st
an
ce
Imb
al
anc
e
Im
pro
pe
r in
st
al
lat
ion
,
lo
ose
ness
P
art
s interference
W
he
el be
arin
g da
ma
ge
PR
OP
EL
LE
R
S
H
A
F
T
FRO
N
T FINAL DRIVE
DRIV
E SHAFT
W
H
EEL H
U
B
S
U
S
PENSION
TI
RE
S
ROAD W
H
EEL
BR
AK
E
S
S
T
EERING
Symptom
DRIVE SHAFT
Noise, Vibration
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
WHEEL HUB
Noise
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Shudder
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
WHEEL HUB
FAX-5
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
PERIODIC MAINTENANCE
WHEEL HUB
On-Vehicle Inspection and Service
INFOID:0000000006161623
Make sure the mounting conditions (looseness, backlash) of each component and component status (wear,
damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub in the axial direction by hand. Make sure there is
no looseness of wheel bearing.
• Rotate wheel hub and make sure there is no unusual noise or
other irregular conditions. If there are any irregular conditions,
replace wheel hub and bearing assembly.
Axial end
play limit
: Refer to
.
SMA571A
FAX-6
< UNIT REMOVAL AND INSTALLATION >
WHEEL HUB
UNIT REMOVAL AND INSTALLATION
WHEEL HUB
Removal and Installation
INFOID:0000000006161624
REMOVAL
1. Remove wheel and tire using power tool.
2. Remove engine undercover if equipped, using power tool.
3. Without disassembling the hydraulic lines, remove the torque member bolts using power tool. Then repo-
sition brake caliper aside with wire. Refer to
BR-32, "Removal and Installation of Brake Caliper and
NOTE:
Do not press brake pedal while brake caliper is removed.
4. Put alignment mark on disc rotor and wheel hub and bearing
assembly, then remove disc rotor.
5. Remove wheel sensor. Refer to
BRC-113, "Removal and Installation"
.
• Inspect the wheel sensor O-ring, replace the wheel sensor assembly if damaged.
• Clean the wheel sensor hole and mounting surface with a suitable brake cleaner and clean lint-free
shop rag. Be careful that dirt and debris do not enter the axle bearing area.
• Apply a coat of suitable grease to the wheel sensor O-ring and mounting hole.
CAUTION:
Do not pull on the wheel sensor harness.
6. On 4WD models, remove drive shaft from steering knuckle. Refer to
FAX-8, "Removal and Installation"
7. Remove wheel hub and bearing assembly bolts using power tool.
1.
Disc rotor
2.
Wheel hub and bearing assembly
3.
Wheel stud
4.
Splash guard
5.
Steering knuckle
Front
AWDIA0423GB
WDIA0044E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст