Nissan Titan A60. Instruction — part 39
ADP-146
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006163591
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Work
INFOID:0000000006163592
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and keep them.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After re-installation is completed, be sure to check that each part works normally.
• Follow the steps below to clean components.
- Water soluble foul: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the
fouled area.
Then rub with a soft and dry cloth.
- Oily foul: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the fouled area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
PREPARATION
ADP-147
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000006163593
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000006163594
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-39570)
Chassis ear
Locating the noise
—
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairing the cause of noise
—
(J-46534)
Trim Tool Set
Removing trim components
SIIA0993E
SIIA0994E
AWJIA0483ZZ
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine ear
Locating the noise
SIIA0995E
ADP-148
< UNIT REMOVAL AND INSTALLATION >
DRIVER SEAT CONTROL UNIT
UNIT REMOVAL AND INSTALLATION
DRIVER SEAT CONTROL UNIT
Removal and Installation
INFOID:0000000006163595
The driver seat control unit is part of the driver seat. Remove the driver seat, then the driver seat control unit.
SE-30, "Removal and Installation For Front Seat"
.
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
ADP-149
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
Removal and Installation
INFOID:0000000006163596
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
REMOVAL
1. Remove the instrument lower panel LH. Refer to
IP-17, "Removal and Installation"
.
2. Remove the lower knee protector.
3. Remove the screw from the automatic drive positioner control
unit (1).
4. Remove automatic drive positioner control unit (1) from bracket
and disconnect electrical connectors.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Clamp the harness in position.
ALIIA0241ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст