Nissan Note E12. Instruction — part 332
FUEL TANK
FL-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
3. Open fuel filler lid.
4. Open fuel filler cap and release the pressure inside fuel tank.
5. Remove the rear seat cushion. Refer to
SE-19, "SEAT CUSHION : Removal and Installation"
.
6. Remove the inspection hole cover.
NOTE:
Inspection hole cover is held by an adhesive.
7. Disconnect the harness connector (B), fuel feed tube (C) and
EVAP tube (A).
Remove the quick connector as follows:
• Hold the sides of the connector, push in tabs (B) and pull (A)
out the tube.
• If the connector and the tube are stuck together, push and pull
several times until they start to move. Then disconnect them
by pulling.
CAUTION:
• Quick connector (1) can be disconnected when the tabs
(F) are depressed completely. Do not twist it more than
necessary.
• Do not use any tools to disconnected quick connector.
• Keep resin tube (C) away from heat. Be especially careful
when welding near the resin tube.
• Prevent acid liquid such as battery electrolyte, etc. from
getting on resin tube.
• Do not bend or twist resin tube during installation and dis-
connection.
• Do not remove the remaining retainer (2) on hard tube (or
the equivalent) (A) except when resin tube or retainer is
replaced.
• When resin tube or hard tube (or the equivalent) is
replaced, also replace retainer with new one.
: Front
ALBIA1150ZZ
JPBIA0134ZZ
(B)
: Connection (cross-section)
(D)
: To under floor fuel line
(E)
: To fuel tank
(G)
: Disconnection
Retainer color
: Blue
JPBIA0130ZZ
FL-12
< REMOVAL AND INSTALLATION >
FUEL TANK
• To keep the connecting portion clean and to avoid dam-
age and foreign materials, cover them completely with
plastic bags (A) or something similar.
8. Remove center muffler. Refer to
9. Remove nut (A) and remove center floor insulators.
10. Disconnect the rear park brake cable brackets (LH). Refer to
.
11. Disconnect fuel filler hose (2) at fuel filler tube (1) side.
12. Disconnect vent hose (3) from fuel tank side.
13. Support the center part of fuel tank (1) using a suitable jack (A).
14. Remove fuel tank mounting bands (LH/RH).
15. Lower suitable jack carefully to remove fuel tank while holding it by hand.
CAUTION:
Fuel tank may be in an unstable condition because of the shape of fuel tank bottom. Be sure to
hold tank securely.
16. If replacing the fuel tank, remove the fuel level sensor unit, fuel filter and fuel pump assembly to transfer to
the new fuel tank.
CAUTION:
JPBIA0135ZZ
ALBIA1147ZZ
JPBIA3423ZZ
JPBIA3424ZZ
FUEL TANK
FL-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
Do not reuse O-ring.
INSTALLATION
Installation is in the reverse order of removal.
Fuel Filler Hose
• Insert fuel filler hose to the length below.
• Be sure hose clamp is not placed on swelled area of fuel filler tube.
• Install fuel filler hose to fuel tank, paying attention to install mark.
EVAP Hose
1. Check connections for damage or foreign material.
2. Align the matching side connection part with the center of shaft, and insert connector straight until a "click"
sound is heard.
Inspection
INFOID:0000000009445838
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn ignition switch “ON” (with engine stopped), then check fuel system connections for leaks by applying
fuel pressure to fuel piping.
2. Start engine and let it idle and check there are no fuel leaks at the fuel system connections.
Fuel filler hose
: 35 mm (1.38 in)
The other hose
: 25 mm (0.98 in)
FL-14
< REMOVAL AND INSTALLATION >
EVAP CANISTER
EVAP CANISTER
Exploded View
INFOID:0000000009445839
Removal and Installation
INFOID:0000000009445840
NOTE:
The EVAP canister vent control valve and EVAP canister system pressure sensor can be removed without
removing the EVAP canister.
REMOVAL
1. Remove battery. Refer to
PG-69, "Removal and Installation (Battery)"
.
2. Remove the TCM (if equipped). Refer to
TM-235, "Removal and Installation"
.
3. Remove the battery tray.
4. Remove IPDM E/R bracket, IPDM E/R and position aside. Refer to
PCS-30, "Removal and Installation"
.
5. Remove EVAP canister cover.
6. Disconnect EVAP canister purge hose, EVAP canister hose and Evap hose from the EVAP canister.
1.
EVAP breather valve
2.
EVAP canister drain hose
3.
EVAP canister hose
4.
EVAP hose
5.
EVAP canister assembly
A.
To EVAP control hose
Front
ALBIA0765ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст