Nissan Note E12. Instruction — part 678
WCS
SYSTEM
WCS-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
PARKING BRAKE RELEASE WARNING CHIME
PARKING BRAKE RELEASE WARNING CHIME : Parking Brake Release Warning
Chime
INFOID:0000000009541201
SYSTEM DIAGRAM
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions are fulfilled.
SIGNAL PATH
Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-
essary from signals below.
Combination switch signal
Combination switch (Lighting switch)
BCM
Driver door switch signal
Front door switch LH
BCM
Signal name
Signal source
Buzzer output signal
BCM
Combination
meter
Signal name
Signal source
JSNIA2422GB
Operation conditions
Ignition switch
ON
Parking brake
During the operation (parking brake switch ON)
Vehicle speed
Approximately 7 km/h (4.3 MPH) or more
Operation conditions
Ignition switch
OFF
Parking brake
Release condition (parking brake switch OFF)
Vehicle speed
Approximately 3 km/h (1.9 MPH) or less
Signal name
Signal source
Ignition switch signal
—
WCS-8
< SYSTEM DESCRIPTION >
SYSTEM
SEAT BELT WARNING CHIME
SEAT BELT WARNING CHIME : Seat belt Warning
INFOID:0000000009541203
SYSTEM DIAGRAM
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges seat belt warning chime is nec-
essary from signals below.
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
Parking brake switch signal
Parking brake switch
Combination meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
Signal name
Signal source
AWNIA2652GB
Operation conditions
Ignition switch
ON
Driver seat belt
Unfastened [seat belt buckle switch LH ON]
Operation conditions
Ignition switch
OFF
Driver seat belt
Fastened (seat belt buckle switch LH OFF)
6 seconds after the start of warning sound
Signal name
Signal source
Ignition switch signal
—
Seat belt buckle switch signal LH
Seat belt buckle switch LH
Combination meter
BCM
Signal name
Signal source
Buzzer output signal
BCM
Combination meter
WCS
DIAGNOSIS SYSTEM (COMBINATION METER)
WCS-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DIAGNOSIS SYSTEM (COMBINATION METER)
On Board Diagnosis Function
INFOID:0000000009641732
ON BOARD DIAGNOSIS ITEM
Information display, speedometer and tachometer can be checked in self-diagnosis mode.
STARTING COMBINATION METER SELF-DIAGNOSIS MODE
METHOD OF STARTING
1. Turn ignition switch ON, and switch the trip meter to “trip A” or “trip B”.
2. Turn ignition switch to OFF.
3. While pressing the meter control switch (1), turn the ignition
switch ON.
4. Make sure that the trip meter displays “0000.0”.
5. Press the meter control switch (1) at least 3 times. (Within 7 sec-
onds after the ignition switch is turned ON).
6. The combination meter is turned to self-diagnosis mode.
• All segments of the information display and shift position indi-
cator (A) for CVT models are displayed.
NOTE:
• Check combination meter power supply and ground circuit when the self-diagnosis mode of the combination
meter does not start. replace combination meter if power supply and ground circuit are normal.
• If any of the segments are not displayed, replace combination meter.
7. Each meter activates by pressing the meter control switch.
JSNIA3904ZZ
JSNIA3900ZZ
AWNIA2440ZZ
WCS-10
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
NOTE:
• If any of the meters or gauges is not activated, replace combination meter.
• The figure is reference.
CONSULT Function
INFOID:0000000009641733
APPLICATION ITEMS
CONSULT can display each diagnostic item using the diagnostic test modes shown.
SELF DIAG RESULT
.
DATA MONITOR
Display Item List
X: Applicable
METER/M&A Diagnosis mode
Description
SELF DIAGNOSTIC RESULT
The combination meter self-diagnosis results.
Data Monitor
Displays combination meter input/output data in real time.
Warning History
Lighting history of the warning lamp and indicator lamp can be checked.
Display item [Unit]
MAIN
SIGNALS
Description
SPEED METER
[km/h] or [mph]
X
Displays the value of vehicle speed signal.
SPEED OUTPUT
[km/h] or [mph]
X
Displays the value of vehicle speed signal, which is transmitted to each unit with
CAN communication.
ODO OUTPUT
[km/h or mph]
Displays odometer signal value transmitted to other units via CAN communica-
tion.
TACHO METER
[rpm]
X
Displays the value of engine speed signal, which is input from ECM.
FUEL METER
[L]
X
Displays the fuel level.
W TEMP METER
[
°C] or [°F]
X
Displays the value of engine coolant temperature signal, which is input from ECM.
ABS W/L
[ON/OFF]
Displays [ON/OFF] condition of ABS warning indicator
BRAKE W/L
[ON/OFF]
Displays [ON/OFF] condition of brake warning indicator.
DOOR W/L
[ON/OFF]
Displays [ON/OFF] condition of door warning indicator.
HI-BEAM IND
[ON/OFF]
Displays [ON/OFF] condition of high beam indicator.
TURN IND
[ON/OFF]
Displays [ON/OFF] condition of turn indicator.
LIGHT IND
[ON/OFF]
Displays [ON/OFF] condition of light indicator.
OIL W/L
[ON/OFF]
Displays [ON/OFF] condition of engine oil pressure warning indicator.
MIL
[ON/OFF]
Displays [ON/OFF] condition of malfunction indicator.
CRUISE IND
[Off]
Displays [ON/OFF] condition of CRUISE indicator.
O/D OFF IND
[ON/OFF]
Displays [ON/OFF] condition of O/D OFF indicator.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст