Nissan Note E12. Instruction — part 272
EM-88
< UNIT REMOVAL AND INSTALLATION >
[HR16DE]
ENGINE ASSEMBLY
22. Use a suitable jack (A) to securely support the bottom of the
engine and the transaxle assembly.
CAUTION:
Put a piece of wood or an equivalent as the supporting sur-
face and secure in a stable condition.
23. Remove engine mounting insulator (RH) (1).
24. Remove engine through bolt-securing nut (C).
25. Carefully lower suitable jack, or raise lift to remove the engine and the transaxle assembly. Observe the
following cautions:
CAUTION:
• Check that no part interferes with the vehicle side.
• Before and during lifting, always check if any harnesses are left connected.
• During removal, always be careful to prevent the vehicle from falling off the lift due to changes in
the center of gravity.
• If necessary, support the vehicle by setting jack or suitable tool at the rear.
26. Remove starter motor. Refer to
.
27. Lift with a hoist and separate the engine from the transaxle assembly. Refer to
(CVT models).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not allow engine oil to get on engine mounting insulator. Be careful not to damage engine mount-
ing insulator.
• Check that each mounting insulator is seated properly, and tighten nuts and bolts.
• When installation directions are specified, install parts according to the direction marks on them,
referring to the figure of components. Refer to
Engine Mounting Insulator (RH)
• Tighten bolts in the numerical order as shown.
INSPECTION AFTER INSTALLATION
PBIC3223J
(2)
: Engine mounting insulator (LH)
(A)
: Engine front side
(B)
: Transaxle side
JSBIA1223ZZ
: Front
JPBIA2809ZZ
ENGINE ASSEMBLY
EM-89
< UNIT REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
.
• Use procedure below to check for fuel leaks.
• Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leaks
at connection points.
• Start engine. With engine speed increased, check again for fuel leaks at connection points.
• Run engine to check for unusual noise and vibration.
NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal and installation, slack in the guide
may generate a pounding noise during and just after engine start. However, this is normal. Noise will stop
after hydraulic pressure rises.
• Warm up engine thoroughly to make sure there are no leaks of fuel, exhaust gas, or any oils/fluids including
engine oil and engine coolant.
• Bleed air from passages in lines and hoses, such as in cooling system.
• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to spec-
ified level, if necessary.
• Summary of the inspection items:
*Power steering fluid, brake fluid, etc.
Item
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leaks
Level
Engine oil
Level
Leaks
Level
Transmission/
transaxle fluid
CVT Models
Leaks
Level/Leaks
Leaks
M/T Models
Level/Leaks
Leaks
Level/Leaks
Other oils and fluids*
Level
Leaks
Level
Fuel
Leaks
Leaks
Leaks
Exhaust gas
—
Leaks
—
EM-90
< UNIT DISASSEMBLY AND ASSEMBLY >
[HR16DE]
ENGINE UNIT
UNIT DISASSEMBLY AND ASSEMBLY
ENGINE UNIT
Setting
INFOID:0000000009444872
NOTE:
The following procedures explain how to disassemble the engine with the engine stand fastened to the bell
housing. Some steps may be different if using a different type of engine stand.
1. Install engine to engine stand:
a. On (M/T models), remove flywheel.
• Secure flywheel (1) using suitable tool (A) and remove bolts.
CAUTION:
• Do not disassemble flywheel.
• Do not place flywheel with signal plate facing down.
• When handling signal plate, take care not to damage or
scratch it.
• Handle signal plate in a manner that prevents it from
becoming magnetized.
b. On (CVT models), remove driveplate.
• Secure driveplate (1) using suitable tool (A) and remove bolts.
CAUTION:
• Do not disassemble flywheel.
• Do not place flywheel or drive plate with signal plate fac-
ing down.
• When handling signal plate, take care not to damage or
scratch it.
• Handle signal plate in a manner that prevents it from
becoming magnetized.
c.
Lift the engine with a hoist to install it onto a widely used engine stand.
CAUTION:
• Use the engine stand that has a load capacity approximately 150 kg (331 lb) or more large
enough for supporting the engine weight.
• If the load capacity of stand is not adequate, remove the following parts beforehand to reduce the poten-
tial risk of overturning stand.
- Intake manifold. Refer to
- Exhaust manifold. Refer to
EM-31, "Removal and Installation"
- Rocker cover. Refer to
NOTE:
The figure shows an example of widely used engine stand (A)
that can support the mating surface of transaxle with flywheel
removed.
CAUTION:
Before removing the hanging chains, check the engine
stand is stable and there is no risk of overturning.
2. Drain engine oil. Refer to
.
CAUTION:
Tool number
: KV11105210 (J-44716)
MBIB1382E
Tool number
: KV11105210 (J-44716)
MBIB1382E
PBIC3227J
ENGINE UNIT
EM-91
< UNIT DISASSEMBLY AND ASSEMBLY >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Be sure to clean drain plug and install with new drain plug washer.
• Do not reuse drain plug washer.
3. Drain engine coolant by removing water drain plug (1) from
inside of the engine.
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
Disassembly
INFOID:0000000009444873
1. Remove intake manifold. Refer to
2. Remove exhaust manifold. Refer to
.
3. Remove oil pan (lower). Refer to
4. Remove ignition coil, spark plug, and rocker cover. Refer to
5. Remove fuel injector and fuel tube. Refer to
6. Remove front cover and timing chain. Refer to
.
7. Remove camshaft. Refer to
8. Remove cylinder head. Refer to
Assembly
INFOID:0000000009444874
Assembly is in the reverse order of disassembly.
: Engine front
Water drain plug
tightening torque
: Refer to
AWBIA1607ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст