Nissan Note E12. Instruction — part 602
C1610 ENGINE STATUS SIGNAL
STC-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
H
I
J
K
L
M
A
B
STC
N
O
P
C1610 ENGINE STATUS SIGNAL
Description
INFOID:0000000009578770
EPS control unit receives the engine status signal from ECM via CAN communication line.
DTC Logic
INFOID:0000000009578771
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
DTC REPRODUCTION PROCEDURE
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Perform “EPS” self-diagnosis.
Is DTC “C1610” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009578772
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Perform “ENGINE” self-diagnosis. Refer to
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform “EPS” self-diagnosis.
Is DTC “C1610” detected?
YES
>> Replace EPS control unit. Refer to
STC-37, "Removal and Installation"
.
NO
>> Check EPS control unit pin terminals for damage or loose connection with harness connector. If
any item are damaged, repair or replace malfunctioning components.
DTC
Display item
Malfunction detected condition
Possible cause
C1610
CAN ENG RPM
• Malfunction is detected in engine status signal
that is output from ECM via CAN communica-
tion.
• ECM input signal error is detected.
• Harness or connector
• CAN communication line
• EPS control unit
• ECM
- Engine status signal error
STC-28
< DTC/CIRCUIT DIAGNOSIS >
U1000 CAN COMM CIRCUIT
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000009578773
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit communicate data but selectively reads required data only.
DTC Logic
INFOID:0000000009578774
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
DTC REPRODUCTION PROCEDURE
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Perform “EPS” self-diagnosis.
Is DTC “U1000” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009578775
LAN-15, "Trouble Diagnosis Flow Chart"
DTC
Display item
Malfunction detected condition
Possible cause
U1000
CAN COMM CIRCUIT
EPS control unit is not transmitting/re-
ceiving CAN communication signal for 2
seconds or more.
• CAN communication error
• EPS control unit
EPS WARNING LAMP
STC-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
H
I
J
K
L
M
A
B
STC
N
O
P
EPS WARNING LAMP
Component Function Check
INFOID:0000000009578776
1.
CHECK THE ILLUMINATION OF THE EPS WARNING LAMP
Check that the EPS warning lamp turns ON when ignition switch turns ON. Then, EPS warning lamp turns
OFF after the engine is started.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Perform trouble diagnosis. Refer to
Diagnosis Procedure
INFOID:0000000009578777
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Perform “EPS” self-diagnosis.
Is any DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
CHECK EPS WARNING LAMP SIGNAL
With CONSULT
1. Turn the ignition switch ON.
CAUTION:
Never start the engine.
2. Select “DATA MONITOR” of “EPS” and select “WARNING LAMP”.
3. Check that the EPS warning lamp is turned ON.
4. Start the engine.
CAUTION:
Never drive the vehicle.
5. Check that the EPS warning lamp is turned OFF.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for combination meter power supply circuit. Refer to
"COMBINATION METER : Diagnosis Procedure"
.
NO
>> Replace the EPS control unit. Refer to
STC-30
< SYMPTOM DIAGNOSIS >
EPS WARNING LAMP DOES NOT TURN ON
SYMPTOM DIAGNOSIS
EPS WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000009485801
EPS warning lamp does not turn ON when turning ignition switch ON from OFF. (Check the illumination of the
EPS warning lamp.)
Diagnosis Procedure
INFOID:0000000009485802
1.
CHECK EPS WARNING LAMP
Perform the trouble diagnosis of EPS warning lamp. Refer to
Is the inspection result normal?
YES
>> Check that there is no malfunction in each harness connector pin terminal or disconnection.
NO
>> Repair or replace the specific malfunctioning part.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст